Homing A Axis
Homing A Axis
Merry Christmas / Happy New Year!!
Do any of you have a home switch on your A / Rotary
axis???
If so how did you mount and what did you use?
Thanks
olf20 / Bob
Do any of you have a home switch on your A / Rotary
axis???
If so how did you mount and what did you use?
Thanks
olf20 / Bob
Re: Homing A Axis
I converted a rotary table but I didn't bother with a home switch, it's set to home wit the other axis in mach.
I don't think a homing switch is needed either as the axis effectivly has no end.
Steve
I don't think a homing switch is needed either as the axis effectivly has no end.
Steve
Re: Homing A Axis
That's what I was thinking, but just wanted some input from some you
you guys that have thought this thru.
Thanks again!
olf20 / Bob
you guys that have thought this thru.
Thanks again!
olf20 / Bob
-
- Vectric Wizard
- Posts: 1000
- Joined: Fri Sep 21, 2007 1:44 pm
- Model of CNC Machine: UCCNC Router, Plasma, Laser
- Location: Australia 3781
Re: Homing A Axis
I think that when you start using the 4th axis a bit, it won't be long before you wish you had a home switch.
Just like on a linear axis, a home switch is good for re-finding zero position after an interruption, for whatever reason.
Greg
Just like on a linear axis, a home switch is good for re-finding zero position after an interruption, for whatever reason.
Greg
Re: Homing A Axis
There are 2 ways to make the rotary axis home.
1. Cheap and easy way. Make a hole in the part of the rotary that rotates, make a tapered pin in the solid part that slides into the hole on the rotary, and always start from there and set your start zero. In the event something happens and the machine quits, or loss if electricity, or a breakdown, you can insert the pin and give yourself the exact starting point to go back and finish the piece.
2. With a switch, you have choices of light beam, or contact style, with an indicator on the rotary that breaks the electrical connection.
1. Cheap and easy way. Make a hole in the part of the rotary that rotates, make a tapered pin in the solid part that slides into the hole on the rotary, and always start from there and set your start zero. In the event something happens and the machine quits, or loss if electricity, or a breakdown, you can insert the pin and give yourself the exact starting point to go back and finish the piece.
2. With a switch, you have choices of light beam, or contact style, with an indicator on the rotary that breaks the electrical connection.
Re: Homing A Axis
I use this interrupt switch from cnc4pc, it has a lot of uses with Mach3such as rpm, homing switch, limit switch, etc.
- metalworkz
- Vectric Wizard
- Posts: 2463
- Joined: Mon Mar 31, 2008 3:26 am
- Model of CNC Machine: SX3 CNC, DIY 24x20 & 48x60 routers
- Location: Modesto, California 95358 USA
Re: Homing A Axis
Hello,
I am thinking a pin mounted near the perimeter of a disk mounted on the outboard end of the headstock spindle could trip a limit switch when the part has rotated 360º and serve as the home switch. Does this sound like a reasonable way to mount the home switch for a rotary, or is there a better way?
I am thinking a pin mounted near the perimeter of a disk mounted on the outboard end of the headstock spindle could trip a limit switch when the part has rotated 360º and serve as the home switch. Does this sound like a reasonable way to mount the home switch for a rotary, or is there a better way?
-
- Vectric Wizard
- Posts: 1000
- Joined: Fri Sep 21, 2007 1:44 pm
- Model of CNC Machine: UCCNC Router, Plasma, Laser
- Location: Australia 3781
Re: Homing A Axis
Wes
Looking at your part completed headstock, I gather that this will be enclosed when finished.
Photo interrupters make good home switches but are susceptible to sawdust. Mounted inside the enclosure this should not be a problem.
How about a disk on the shaft, with either a tab or a slot. You have plenty of room in there.
Greg
Looking at your part completed headstock, I gather that this will be enclosed when finished.
Photo interrupters make good home switches but are susceptible to sawdust. Mounted inside the enclosure this should not be a problem.
How about a disk on the shaft, with either a tab or a slot. You have plenty of room in there.
Greg
- metalworkz
- Vectric Wizard
- Posts: 2463
- Joined: Mon Mar 31, 2008 3:26 am
- Model of CNC Machine: SX3 CNC, DIY 24x20 & 48x60 routers
- Location: Modesto, California 95358 USA
Re: Homing A Axis
Hi Greg,
Yes, I have a cover for the top side but will need to fabricate a cover for the right side as I wasn't sure where the motor would be when I began the design. I have those photo interrupter type switches on my SX3 mill and they seem to work fine. Your idea to place the switch inside sounds like a good way to go as there is plenty of room there and then it will be enclosed in the headstock. Thanks for the suggestion, I will look into implementing it.
Yes, I have a cover for the top side but will need to fabricate a cover for the right side as I wasn't sure where the motor would be when I began the design. I have those photo interrupter type switches on my SX3 mill and they seem to work fine. Your idea to place the switch inside sounds like a good way to go as there is plenty of room there and then it will be enclosed in the headstock. Thanks for the suggestion, I will look into implementing it.
Re: Homing A Axis
Just something to bear in mind guys..
when you home an X, Y or Z axis you'll always approach the home switch from the same direction,
so you'll always get the same position.
When you home a rotary axis it's possible to approach the switch from either side, (depending where your axis has stopped and your control software)
If you use a cam switch there'll be a big difference between one direction and the other.
when you home an X, Y or Z axis you'll always approach the home switch from the same direction,
so you'll always get the same position.
When you home a rotary axis it's possible to approach the switch from either side, (depending where your axis has stopped and your control software)
If you use a cam switch there'll be a big difference between one direction and the other.
Re: Homing A Axis
My internet connection is a tethered telephone, and sometimes it is not so good. In my earlier post I had intended to post an address for a photo coupler switch which is easy to hook up and use, so here it is now..........maybe.
http://www.cnc4pc.com/Store/osc/product ... cts_id=129
http://www.cnc4pc.com/Store/osc/product ... cts_id=129
-
- Vectric Wizard
- Posts: 1000
- Joined: Fri Sep 21, 2007 1:44 pm
- Model of CNC Machine: UCCNC Router, Plasma, Laser
- Location: Australia 3781
Re: Homing A Axis
If you are using Mach3 then homing direction is a setting, so this will not happen.Timvmax wrote:Just something to bear in mind guys..
when you home an X, Y or Z axis you'll always approach the home switch from the same direction,
so you'll always get the same position.
When you home a rotary axis it's possible to approach the switch from either side, (depending where your axis has stopped and your control software)
If you use a cam switch there'll be a big difference between one direction and the other.
I have no experience with any other controllers.
Greg
Re: Homing A Axis
Well it did not take long! I hand coded a spiral / auger twist to make my grandson
a working grain auger. When cutting each pass it took a long time to return to the
start position / home.
I'm using a rotary table with a stepper, but I think if I continue with this I may have
to build my own spindle. However I want to be able to have my chuck / spindle either
horizontal or vertical.
Either way I will have to get my homing switch hooked up.
olf20 / Bob
a working grain auger. When cutting each pass it took a long time to return to the
start position / home.
I'm using a rotary table with a stepper, but I think if I continue with this I may have
to build my own spindle. However I want to be able to have my chuck / spindle either
horizontal or vertical.
Either way I will have to get my homing switch hooked up.
olf20 / Bob