A little something
- Makingtoothpicks
- Vectric Wizard
- Posts: 520
- Joined: Tue Jul 23, 2013 8:46 pm
- Model of CNC Machine: Cncrouterparts CPR2448
- Location: Burien, Wa
- Contact:
A little something
Something I am working on. I have a redesigned it. Practicing my non artistic abilities.
Thank You for looking
Don
Thank You for looking
Don
- TReischl
- Vectric Wizard
- Posts: 4600
- Joined: Thu Jan 18, 2007 6:04 pm
- Model of CNC Machine: 8020 48X36X7 RP 2022 UCCNC Screenset
- Location: Leland NC
Re: A little something
Looks good!
A very unique finish that makes it look really, REALLY old, nicely done.
A very unique finish that makes it look really, REALLY old, nicely done.
"If you see a good fight, get in it." Dr. Vernon Johns
- Leo
- Vectric Wizard
- Posts: 4084
- Joined: Sat Jul 14, 2007 3:02 am
- Model of CNC Machine: 1300 x 1300 x 254 Chinese Made
- Location: East Freetown, Ma.
- Contact:
Re: A little something
??????? non-artistic ???????
NOT from where I am standing
That is superior ability
Fantastic job.
NOT from where I am standing
That is superior ability
Fantastic job.
Imagine the Possibilities of a Creative mind, combined with the functionality of CNC
- mtylerfl
- Vectric Archimage
- Posts: 5865
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: A little something
Nice job, Don! “Old-World” finish effect!
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
- Tex_Lawrence
- Vectric Wizard
- Posts: 932
- Joined: Fri Mar 25, 2016 11:30 am
- Model of CNC Machine: Shapeoko3XXL; JTech7W; V-CarvePro 11.554
- Location: Dayton, Texas (Don't Mess With My Texas!)
Re: A little something
Ditto on what others have posted! I really thought you were somehow over-carving a cast piece.
FYI, (not to take away from your art) that Vbit cut on-the-line around the perimeter could use a bit of offset to the outside (or the point is broken). I noticed because that started happening to my cuts.
Nice, very nice! +1
FYI, (not to take away from your art) that Vbit cut on-the-line around the perimeter could use a bit of offset to the outside (or the point is broken). I noticed because that started happening to my cuts.
Nice, very nice! +1
Tex — Crooked Wood Products
Now there's a man with an open mind – you can feel the breeze from here.
Now there's a man with an open mind – you can feel the breeze from here.
- rgerding
- Vectric Craftsman
- Posts: 127
- Joined: Mon Nov 28, 2016 7:29 pm
- Model of CNC Machine: Iconic 2015
- Location: Ottawa,OH
Re: A little something
Very nice. Is the material corian or something like it?
Ron
Ron
Ron
If sawdust were gold, I'd be very rich
If sawdust were gold, I'd be very rich
-
- Vectric Craftsman
- Posts: 193
- Joined: Sun Nov 04, 2012 4:27 pm
- Model of CNC Machine: PRS Buddy48alpha ,4x6' 130w laser, Wazer
Re: A little something
Very nice, I use a lot of corian [and similar] on both the CNC and CO2 laser.
- Makingtoothpicks
- Vectric Wizard
- Posts: 520
- Joined: Tue Jul 23, 2013 8:46 pm
- Model of CNC Machine: Cncrouterparts CPR2448
- Location: Burien, Wa
- Contact:
Re: A little something
Yes it is Corian or something like it. It was a cut off and given to me.
- Makingtoothpicks
- Vectric Wizard
- Posts: 520
- Joined: Tue Jul 23, 2013 8:46 pm
- Model of CNC Machine: Cncrouterparts CPR2448
- Location: Burien, Wa
- Contact:
Re: A little something
I am not sure what you are referring to. The outside profile cut was a straight end mill. The only place I used a V-bit was the text.Tex_Lawrence wrote: ↑Fri Jul 17, 2020 2:49 pmDitto on what others have posted! I really thought you were somehow over-carving a cast piece.
FYI, (not to take away from your art) that Vbit cut on-the-line around the perimeter could use a bit of offset to the outside (or the point is broken). I noticed because that started happening to my cuts.
Nice, very nice! +1
tools used 1/16 tapered ball nose , 1/8 end mill ,90 deg V bit
Don
- Tex_Lawrence
- Vectric Wizard
- Posts: 932
- Joined: Fri Mar 25, 2016 11:30 am
- Model of CNC Machine: Shapeoko3XXL; JTech7W; V-CarvePro 11.554
- Location: Dayton, Texas (Don't Mess With My Texas!)
Re: A little something
What I was referring to was the small edge Vee around the profile. Perhaps this was intentional? Not trying to be picky; just interested.
Tex — Crooked Wood Products
Now there's a man with an open mind – you can feel the breeze from here.
Now there's a man with an open mind – you can feel the breeze from here.
-
- Vectric Wizard
- Posts: 409
- Joined: Thu Apr 06, 2017 3:07 am
- Model of CNC Machine: Camaster Stinger SR24
- Location: Addison, PA
Re: A little something
Your artistic abilities are commendable. Excellent job. I love the look of the finish. I also love working with Corian.
Joe
I have a chip on my shoulder....several more in my hair and lots more all over my shop floor.
I have a chip on my shoulder....several more in my hair and lots more all over my shop floor.
- Makingtoothpicks
- Vectric Wizard
- Posts: 520
- Joined: Tue Jul 23, 2013 8:46 pm
- Model of CNC Machine: Cncrouterparts CPR2448
- Location: Burien, Wa
- Contact:
Re: A little something
You are not being picky. I appreciate your input. It was not intentional. This was a test so I could see whatTex_Lawrence wrote: ↑Sat Jul 18, 2020 1:34 pmWhat I was referring to was the small edge Vee around the profile. Perhaps this was intentional? Not trying to be picky; just interested.
needs improving. On my next one a will look closer at that.
Thank You
Don
-
- Posts: 38
- Joined: Thu Apr 30, 2015 8:23 pm
- Model of CNC Machine: Shopbot
Re: A little something
That looks great, wish I had your abilities but at my old age I will just muddle through with simpler items.
Joe
Joe