New handle for old saw
-
- Vectric Wizard
- Posts: 594
- Joined: Wed Mar 27, 2013 4:16 pm
- Model of CNC Machine: CNC Shark Pro Plus
- Contact:
New handle for old saw
This is a new saw handle that I made. I did the basic design in other software, this was my first time using that software and I did the basic shape and radii there and saved it as an STL. I then imported that STL into Aspire and I used the two-sided machining feature to complete the design by adding the finger grips, an indent for the index finger, and my logo.
This is a Richardson Bros. of Newark, NJ saw that was manufactured between 1878 and 1890. The blade still has plenty of life. The original handle had a crack in it with a nail holding it together. I will keep that around.
Making one of these by hand is a long process. 45 minutes or so of CNC carving got me about 90% of the way.
Next, I have to work on a saw vice so I can sharpen this.
This is a Richardson Bros. of Newark, NJ saw that was manufactured between 1878 and 1890. The blade still has plenty of life. The original handle had a crack in it with a nail holding it together. I will keep that around.
Making one of these by hand is a long process. 45 minutes or so of CNC carving got me about 90% of the way.
Next, I have to work on a saw vice so I can sharpen this.
BillK
https://www.facebook.com/CarvingsByKurtz
https://www.facebook.com/CarvingsByKurtz
- jarm2
- Vectric Craftsman
- Posts: 246
- Joined: Wed Jun 13, 2012 9:16 pm
- Model of CNC Machine: C&CNC electronics 4x4 ext aluminum table
- Location: Harpster, Idaho
Re: New handle for old saw
Very nicely done. I have a good saw with a plastic handle and will use your idea to make a new handle out of wood. Great idea.
Aspire 11 ViaCAD Pro 12 Corel 2019 W 10, 2.2 kw spindle wireless pendant
- scottp55
- Vectric Wizard
- Posts: 4717
- Joined: Thu May 09, 2013 11:30 am
- Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP11.5
- Location: Kennebunkport, Maine, US
Re: New handle for old saw
Looks VERY comfortable and easy to control...Well Done Bill!
LIKING it!
scott
LIKING it!
scott
I've learned my lesson well. You can't please everyone,so you have to please yourself
R.N.
R.N.
- mtylerfl
- Vectric Archimage
- Posts: 5892
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: New handle for old saw
I like this idea! I have two saws that could use nice handles like that. Thank you for your inspiration!
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
-
- Vectric Wizard
- Posts: 594
- Joined: Wed Mar 27, 2013 4:16 pm
- Model of CNC Machine: CNC Shark Pro Plus
- Contact:
Re: New handle for old saw
Thanks all. I have 2 or 3 other saws in line for handle replacement. May try a plane tote next though.
BillK
https://www.facebook.com/CarvingsByKurtz
https://www.facebook.com/CarvingsByKurtz
-
- Vectric Craftsman
- Posts: 289
- Joined: Mon Dec 01, 2014 3:53 pm
- Model of CNC Machine: Homemade
New handle for old saw
inspirational the finger indents.
-
- Vectric Wizard
- Posts: 594
- Joined: Wed Mar 27, 2013 4:16 pm
- Model of CNC Machine: CNC Shark Pro Plus
- Contact:
Re: New handle for old saw
Yes, they give it a nice comfortable feel.Bobtail Farm wrote:inspirational the finger indents.
BillK
https://www.facebook.com/CarvingsByKurtz
https://www.facebook.com/CarvingsByKurtz
-
- Posts: 36
- Joined: Tue Mar 05, 2013 7:58 pm
- Model of CNC Machine: ShopBot Desktop
- Location: Strathfieldsaye, Australia
Re: New handle for old saw
It's nice to make something that's practical, and useful in the shed no less. Nice job. Handy finger positions.
Graeme Chandler (Australia)
ShopBot Desktop
Aspire 8
ShopBot Desktop
Aspire 8
- Bob Jr
- Vectric Wizard
- Posts: 463
- Joined: Thu Aug 13, 2009 2:13 am
- Model of CNC Machine: Axiom, Shark
Re: New handle for old saw
Bill,
That's one slick handle!
There's a great supply of old saws at our local ReStore. I'll go pick through them and start re-handling a couple.
One question... How did you make such a neat, thin cut into the exact center of the handle in order to insert the blade?
Bob
That's one slick handle!
There's a great supply of old saws at our local ReStore. I'll go pick through them and start re-handling a couple.
One question... How did you make such a neat, thin cut into the exact center of the handle in order to insert the blade?
Bob
"Be accurate."
W. Tell
W. Tell
-
- Vectric Wizard
- Posts: 594
- Joined: Wed Mar 27, 2013 4:16 pm
- Model of CNC Machine: CNC Shark Pro Plus
- Contact:
Re: New handle for old saw
Bob Jr. :
Thanks. I was worried about that cut before I made it. I started by marking and drilling the holes for the saw nuts first. Then I lined it up and cut into the deepest part near the top with a bandsaw with a fence which put me pretty much perfectly on center. It was enough to then use a tenon saw (back saw) to make the full cut to depth. It was a little tight on the blade, so I have a cross cut saw that had a good set and matched the blade width to clean it out to a good fit. Just made it deep enough so that all the holes in the handle line up with the holes in the blade. It helped to have the old handle also.
Thanks. I was worried about that cut before I made it. I started by marking and drilling the holes for the saw nuts first. Then I lined it up and cut into the deepest part near the top with a bandsaw with a fence which put me pretty much perfectly on center. It was enough to then use a tenon saw (back saw) to make the full cut to depth. It was a little tight on the blade, so I have a cross cut saw that had a good set and matched the blade width to clean it out to a good fit. Just made it deep enough so that all the holes in the handle line up with the holes in the blade. It helped to have the old handle also.
BillK
https://www.facebook.com/CarvingsByKurtz
https://www.facebook.com/CarvingsByKurtz
- Bob Jr
- Vectric Wizard
- Posts: 463
- Joined: Thu Aug 13, 2009 2:13 am
- Model of CNC Machine: Axiom, Shark
Re: New handle for old saw
Thank you Bill,
It's funny how what seems like the easiest part of a job can be the most distracting for me.
Thank you for your help.
Bob
It's funny how what seems like the easiest part of a job can be the most distracting for me.
Thank you for your help.
Bob
"Be accurate."
W. Tell
W. Tell
-
- Vectric Wizard
- Posts: 594
- Joined: Wed Mar 27, 2013 4:16 pm
- Model of CNC Machine: CNC Shark Pro Plus
- Contact:
Re: New handle for old saw
Back at it again....
An old saw, lightly used, but probably left outside for a while. Missing two saw nuts, handle with a crack through. So I had fun changing the design up to custom make a new one. Added the ribbon detail to this one. Really liked using the Level selector for maching the overall face with 1/4 ball mill, then selecting the other level with the ribbon and machining that with a 1 mm TBN. Throw away your rest machining techniques and use the level selector to sharpen up the details. About an hour and a half on each side.
I ordered the new saw nuts, be here next week. So I guess I’ll get the slit in and drill the holes next. This like the first one, feels great in my hand.
An old saw, lightly used, but probably left outside for a while. Missing two saw nuts, handle with a crack through. So I had fun changing the design up to custom make a new one. Added the ribbon detail to this one. Really liked using the Level selector for maching the overall face with 1/4 ball mill, then selecting the other level with the ribbon and machining that with a 1 mm TBN. Throw away your rest machining techniques and use the level selector to sharpen up the details. About an hour and a half on each side.
I ordered the new saw nuts, be here next week. So I guess I’ll get the slit in and drill the holes next. This like the first one, feels great in my hand.
BillK
https://www.facebook.com/CarvingsByKurtz
https://www.facebook.com/CarvingsByKurtz
- gkas
- Vectric Wizard
- Posts: 1451
- Joined: Sun Jan 01, 2017 3:39 am
- Model of CNC Machine: Aspire, Axiom AR8 Pro+, Axiom 4.2W Laser
- Location: Southern California
Re: New handle for old saw
Very nice job.... Never having done this, how do you slit the handle?
-
- Vectric Wizard
- Posts: 594
- Joined: Wed Mar 27, 2013 4:16 pm
- Model of CNC Machine: CNC Shark Pro Plus
- Contact:
Re: New handle for old saw
It helps to have the old one to know how deep to go. I start the cut with a bandsaw, holding the handle against the fence. I finish it with a handsaw to sneak up on it. Drilling the holes first and trying the blade until you can see the holes aligned, You want it to be a good fit. Being careful with it, you’ll probably spend 15 minutes doing it.
BillK
https://www.facebook.com/CarvingsByKurtz
https://www.facebook.com/CarvingsByKurtz
- scottp55
- Vectric Wizard
- Posts: 4717
- Joined: Thu May 09, 2013 11:30 am
- Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP11.5
- Location: Kennebunkport, Maine, US
Re: New handle for old saw
Nice job Bill!
Looks like you'll have a bit more comfort and control with the new one.
Looks like you'll have a bit more comfort and control with the new one.
I've learned my lesson well. You can't please everyone,so you have to please yourself
R.N.
R.N.