Free Labs Project - Pencil Box - Take Flight
- Todd Bailey
- Vectric Staff
- Posts: 625
- Joined: Mon Nov 24, 2014 8:40 pm
- Model of CNC Machine: CraftCNC
- Contact:
Free Labs Project - Pencil Box - Take Flight
This month’s project is inspired by my late father whom was almost never seen without his journal, mechanical pencil and stick eraser. Always the same ones and he took pleasure in always knowing where they were. I try to do the same and carry my favorites back and forth to the office. I enjoy the ritual of taking them out of my bag and putting them on my desk. The simple beauty of a device that has the power to make a change, to turn an idea into something I can share and reminds me of my father is, well, something that is hard to put into words.
Of course, a basic pencil box would do the trick, but I wanted it to be more useful, something that adds to my daily routine and maybe, just maybe, helps to tell a very small but special part of my fathers story.
The inlay on the top and the inclusion of the v-carving is another nod to my father. We both shared an interest in flight and without his support in my life choices, teaching me to keep my fears in check I would not be where I am today.
The addition of the mobile phone slot took care of a desk organization problem I have been having. It creates a place to put my mobile while it’s charging so I don’t have to keep looking for it.
Hope you download this free project and make it as is or... "Make it your own."
https://www.vectric.com/vectric-communi ... /PencilBox
Be safe...
Of course, a basic pencil box would do the trick, but I wanted it to be more useful, something that adds to my daily routine and maybe, just maybe, helps to tell a very small but special part of my fathers story.
The inlay on the top and the inclusion of the v-carving is another nod to my father. We both shared an interest in flight and without his support in my life choices, teaching me to keep my fears in check I would not be where I am today.
The addition of the mobile phone slot took care of a desk organization problem I have been having. It creates a place to put my mobile while it’s charging so I don’t have to keep looking for it.
Hope you download this free project and make it as is or... "Make it your own."
https://www.vectric.com/vectric-communi ... /PencilBox
Be safe...
------------------------------------
Todd Bailey | Design and Make
DesignAndMake.com
Todd Bailey | Design and Make
DesignAndMake.com
- Bob Jr
- Vectric Wizard
- Posts: 463
- Joined: Thu Aug 13, 2009 2:13 am
- Model of CNC Machine: Axiom, Shark
Re: Free Labs Project - Pencil Box - Take Flight
Thank you for the pencil box files Todd.
I also appreciate the background story about your Dad, and your thoughts about your project.
Bob
I also appreciate the background story about your Dad, and your thoughts about your project.
Bob
"Be accurate."
W. Tell
W. Tell
- jimwill2
- Vectric Wizard
- Posts: 612
- Joined: Tue Aug 31, 2010 1:48 am
- Model of CNC Machine: CaMaster Stinger w/recoil, FTC
- Location: Parkville, Missouri
Re: Free Labs Project - Pencil Box - Take Flight
Great project and tribute to your father! Thank you for the files and the work you put into the it.
Jim Williams
- mtylerfl
- Vectric Archimage
- Posts: 5896
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: Free Labs Project - Pencil Box - Take Flight
Beautiful project in every way, Todd!
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
- highpockets
- Vectric Wizard
- Posts: 3667
- Joined: Tue Jan 06, 2015 4:04 pm
- Model of CNC Machine: PDJ Pilot Pro
Re: Free Labs Project - Pencil Box - Take Flight
Nice project Todd. Really like the story behind the project...
John
Maker of Chips
Maker of Chips
- Rcnewcomb
- Vectric Archimage
- Posts: 5928
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: Free Labs Project - Pencil Box - Take Flight
My son the pilot is going to love this one.
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
-
- Vectric Wizard
- Posts: 520
- Joined: Sun May 03, 2015 12:25 pm
- Model of CNC Machine: Axiom AR8
- Location: Savannah, GA
Re: Free Labs Project - Pencil Box - Take Flight
Thank you for the project plans. Also appreciate you sharing the story about your father. My oldest daughter will appreciate me making her one these pencil boxes. I gave her a Tombow mechanical pencil last year which would go very nicely in one of these boxes will maybe a little adjustment.
- Todd Bailey
- Vectric Staff
- Posts: 625
- Joined: Mon Nov 24, 2014 8:40 pm
- Model of CNC Machine: CraftCNC
- Contact:
Re: Free Labs Project - Pencil Box - Take Flight
Thanks for all the great comments... I appreciate them all!
------------------------------------
Todd Bailey | Design and Make
DesignAndMake.com
Todd Bailey | Design and Make
DesignAndMake.com
Re: Free Labs Project - Pencil Box - Take Flight
Hi Todd,
Thanks for posting this project. I have a question. I would like to add an inlaid name into the top, but I'm having trouble getting the two half's to line-up. Do you have any advice or tricks to get the male and female parts to mate?
Thanks for posting this project. I have a question. I would like to add an inlaid name into the top, but I'm having trouble getting the two half's to line-up. Do you have any advice or tricks to get the male and female parts to mate?
- Todd Bailey
- Vectric Staff
- Posts: 625
- Joined: Mon Nov 24, 2014 8:40 pm
- Model of CNC Machine: CraftCNC
- Contact:
Re: Free Labs Project - Pencil Box - Take Flight
Hello gene8522...
Glad you like the box!!
Hummm... can you post a picture of your problem?
Thanks...
Glad you like the box!!
Hummm... can you post a picture of your problem?
Thanks...
------------------------------------
Todd Bailey | Design and Make
DesignAndMake.com
Todd Bailey | Design and Make
DesignAndMake.com
Re: Free Labs Project - Pencil Box - Take Flight
Hi Todd,Todd Bailey wrote:Hello gene8522...
Glad you like the box!!
Hummm... can you post a picture of your problem?
Thanks...
I would like to make these boxes for my two granddaughters but with their names on each.
I guess I just don't know how to ask my question. Right now I'm just trying to get the inlays to look right in Aspire 9.5.
I don't have a problem with the female engraving location, but when I try to locate the same text for the male engraving I get lost as to what to use as a starting reference point.
Re: Free Labs Project - Pencil Box - Take Flight
https://www.screencast.com/t/CeS9BA94z
https://www.screencast.com/t/3yxCO2HpP
Where or how would I locate the text on the box top?
https://www.screencast.com/t/3yxCO2HpP
Where or how would I locate the text on the box top?
Re: Free Labs Project - Pencil Box - Take Flight
https://www.screencast.com/t/tFdLXZuKDPXbgene8522 wrote:https://www.screencast.com/t/CeS9BA94z
https://www.screencast.com/t/3yxCO2HpP
Where or how would I locate the text on the box top?
After more thinking. This should be the proper orientation for the text on the male carving.
-
- Vectric Craftsman
- Posts: 130
- Joined: Tue Feb 06, 2018 9:18 pm
- Model of CNC Machine: CNC 6040, Vectric Aspire, UCCNC
- Location: Skane, Sweden
Re: Free Labs Project - Pencil Box - Take Flight
Thank you for a very nice project.
I, after some struggle with inches/mm, did manage to cut the project.
Material is teak, with pine as inlay. It is a gift to our CEO.
Unfortunately i had som struggle with the magnets, but the end result is stunning.
Thanks gain.
I, after some struggle with inches/mm, did manage to cut the project.
Material is teak, with pine as inlay. It is a gift to our CEO.
Unfortunately i had som struggle with the magnets, but the end result is stunning.
Thanks gain.
-
- Vectric Wizard
- Posts: 520
- Joined: Sun May 03, 2015 12:25 pm
- Model of CNC Machine: Axiom AR8
- Location: Savannah, GA
Re: Free Labs Project - Pencil Box - Take Flight
mickecarlsson, The inlay looks very nice and I really like your choice of woods. For tough cuts, such as the pockets for the magnets, I'll may have the cnc make a dimple where the pocket is to be and then use a forstner drill bit to drill the pocket. Also, I may use metal discs opposite magnets sort of like kitchen cabinet magnetic holds. Thank you for posting and you've given me more ideas for when I cut one of these. Did you make the pen?