Cuts right line twice.

This forum is for general discussion about Aspire
Post Reply
sailfl
Vectric Wizard
Posts: 377
Joined: Sat Dec 15, 2007 3:46 pm
Model of CNC Machine: MechMate
Location: Orlando, FL

Cuts right line twice.

Post by sailfl »

I have never seen this problem in all the time I have used Aspire. The right line cuts twice when using outside and inside machine vectors. Only once when on machine vector is used. I would like to understand why it is doing this.

I am still using 4.5 version.

Thanks
Attachments
Save Test.crv3d
(18 KiB) Downloaded 70 times

User avatar
Adrian
Vectric Archimage
Posts: 10582
Joined: Thu Nov 23, 2006 2:19 pm
Model of CNC Machine: ShopBot PRS Alpha 96x48
Location: Surrey, UK

Re: Cuts right line twice.

Post by Adrian »

If you go into node edit mode and drag the bottom node over on that line you'll see the problem. It's basically a double line as far as Aspire is concerned because of the overlap.

User avatar
Rcnewcomb
Vectric Wizard
Posts: 3957
Joined: Fri Nov 04, 2005 5:54 am
Model of CNC Machine: GCnC/WinCNC
Location: San Jose, California, USA
Contact:

Re: Cuts right line twice.

Post by Rcnewcomb »

If you zoom in enough you see the line has an extra point.
(Adrian beat me to it!)
ExtraPoint.JPG
- Randall Newcomb
10 fingers in, 10 fingers out
another good day in the shop

User avatar
TReischl
Vectric Wizard
Posts: 3632
Joined: Thu Jan 18, 2007 6:04 pm
Model of CNC Machine: 8020 Build 48X36X10 RP 2010 Screenset
Location: Leland NC

Re: Cuts right line twice.

Post by TReischl »

The dreaded Double Line Whammy!
"If you see a good fight, get in it." Dr. Vernon Jones

sailfl
Vectric Wizard
Posts: 377
Joined: Sat Dec 15, 2007 3:46 pm
Model of CNC Machine: MechMate
Location: Orlando, FL

Re: Cuts right line twice.

Post by sailfl »

Thank you. I knew it was a problem but I could not find it. It is very small.

User avatar
Xxray
Vectric Wizard
Posts: 2147
Joined: Thu Feb 17, 2011 8:47 am
Model of CNC Machine: CAMaster Stinger 1
Location: MI USA

Re: Cuts right line twice.

Post by Xxray »

TReischl wrote:The dreaded Double Line Whammy!

I'm singin those Double Line Blueeeeesssss !
Doug

User avatar
TReischl
Vectric Wizard
Posts: 3632
Joined: Thu Jan 18, 2007 6:04 pm
Model of CNC Machine: 8020 Build 48X36X10 RP 2010 Screenset
Location: Leland NC

Re: Cuts right line twice.

Post by TReischl »

"Nobody leaves til dey sing da blues."
"If you see a good fight, get in it." Dr. Vernon Jones

fixtureman
Vectric Wizard
Posts: 439
Joined: Fri Jun 06, 2008 4:41 pm

Re: Cuts right line twice.

Post by fixtureman »

TReischl wrote:"Nobody leaves til dey sing da blues."
Is'n that a line from Adventures in Babysitting

User avatar
TReischl
Vectric Wizard
Posts: 3632
Joined: Thu Jan 18, 2007 6:04 pm
Model of CNC Machine: 8020 Build 48X36X10 RP 2010 Screenset
Location: Leland NC

Re: Cuts right line twice.

Post by TReischl »

You win the prize!
"If you see a good fight, get in it." Dr. Vernon Jones

Post Reply