I was asked to make this clock by someone who saw one like it on an Internet search for wooden clocks. Apparently the company was no longer making them. I designed this in Aspire. I changed the sides to make them curve like bowing swans. This was a challenge to make with my shark as the side pieces are 2 inches thick and the bottom is 2 1/4". It's also hard to take a good picture of since the color of the two woods, Ash and Walnut, contrast so much.
Although my own tastes tend more to the traditional, this piece also benefited from the precision of CNC as the fits between the two sides and the clock pendant are pretty seamless and I'm pretty sure I wouldn't have been able to do that with traditional methods.
If you haven't used ash for any project yet, I can say I highly recommend it. It carves beautifully.
Bowing Swans Mantle Clock
-
- Vectric Wizard
- Posts: 772
- Joined: Sat Jan 09, 2010 7:28 am
- Model of CNC Machine: cnc mako shark ext bed with HD 5 gantry
- Location: Buffalo,NY
Re: Bowing Swans Mantle Clock
That is a real nice clock you made, like the 2 different woods used.
Tony
Tony
What will matter is not what you bought but what you built; not what you got, but what you gave
- mtylerfl
- Vectric Archimage
- Posts: 5892
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: Bowing Swans Mantle Clock
That is beautiful - I like it! Thanks for posting.
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
- dhellew2
- Vectric Wizard
- Posts: 1326
- Joined: Thu May 22, 2008 10:14 pm
- Model of CNC Machine: Legacy Artisan 72 and AVID CNC Rotary
- Location: Royal City Washington
Re: Bowing Swans Mantle Clock
Nice job, the text is clean and sharp. Looks like the clock is a pendulum ready to swing back and forth . dh
You will get old if you live long enough!
Young = time, no money
Old = money, no time
Dale
Young = time, no money
Old = money, no time
Dale
-
- Vectric Wizard
- Posts: 594
- Joined: Wed Mar 27, 2013 4:16 pm
- Model of CNC Machine: CNC Shark Pro Plus
- Contact:
Re: Bowing Swans Mantle Clock
Thanks for your kindness. It was fun to make. Hope the bride and groom like it.
BillK
https://www.facebook.com/CarvingsByKurtz
https://www.facebook.com/CarvingsByKurtz
-
- Vectric Apprentice
- Posts: 62
- Joined: Sun Mar 17, 2013 7:48 pm
- Model of CNC Machine: ShopBot Buddy 48T PRS alpha HSD 2.2HP
- Location: Fruitport, MI
Re: Bowing Swans Mantle Clock
The clock is truly a present worthy to give to a royal couple. I notices how you used the grain in wood so it accents the contour of each beak.... that could not be accidental. I certainly wish that could be a project of the month (hint for Aspire to make contact)!! Thanks very much for sharing.
-
- Vectric Wizard
- Posts: 594
- Joined: Wed Mar 27, 2013 4:16 pm
- Model of CNC Machine: CNC Shark Pro Plus
- Contact:
Re: Bowing Swans Mantle Clock
Thanks Joe. I really liked the grain of the ash and realized I would get a nice effect since I tilted the sides in to cut them from a 5 inch wide board. Using Aspire to curve up the fronts further enhanced the effect.
As far as a clock for royals goes, did you know that Reyes translates to Kings in English?
As far as a clock for royals goes, did you know that Reyes translates to Kings in English?
BillK
https://www.facebook.com/CarvingsByKurtz
https://www.facebook.com/CarvingsByKurtz