Easy Organizer Maker gadget

This forum is for users to submit their own gadgets to the community
Post Reply
User avatar
jimandi5000
Vectric Wizard
Posts: 876
Joined: Wed Mar 11, 2015 6:50 pm
Model of CNC Machine: Home Made 60 x 120
Location: North Houston Tx.
Contact:

Easy Organizer Maker gadget

Post by jimandi5000 »

Hello All,

My newest Gadget, it is the Easy Organizer Maker gadget. It creates a organizer from the user entering the number of Rows and Columns. The Organizer is made up of 2 sides, 2 ends, one bottom, and the correct Dividers and Columns. The sides, bottom, dividers, columns and ends can have different thickness material. The gadget supports 3 types of bottom construction styles. It also supports the Dog Bone, Blind Dog Bone, T-Bone Joint, Blind T-Bone, Sniglet Joint and the Blind Sniglet joints. It also creates 3 BOM file types.

This Version 1.5

Supports: 11.0 and up

Install
1. Download the gadget EasyOrganizerMaker.zip that is attached to this post.
2. Rename it from EasyTrayMaker.zip to EasyOrganizerMaker.vgadget
3. In Vectric Pro or Aspire click on Gadgets -> Install Gadget and navigate to where you downloaded the file to, select it and click Ok.

It should give you a pop up saying the gadget was installed and you should see EasyOrganizerMaker in the Gadgets menu.


Steps for Use:

1. Setup a new drawing with the proper material size
2. Run the EasyOrganizerMaker gadget
3. Enter the proper values for the Organizer overall size and the materials thickness for the Organizer parts
4. Open the Project menu, select where to write the Organizer BOMs
5. Open the Milling menu, check the values and select the joint type
6. On the Main menu, select the tooling you use to mill the drawer parts
7. Press the OK button

If you have any issues or questions let me know.
Attachments
2022-04-29 18_40_03-Window.png
2022-04-29 18_39_25-Window.png
2022-04-29 18_39_05-Window.png
2022-04-29 18_35_36-Window.png
2022-04-29 18_34_55-Window.png
EasyOrganizerMaker.zip
Rename to: EasyOrganizerMaker.vgadget
(39.41 KiB) Downloaded 83 times
Thanks,
Jim

User avatar
sharkcutup
Vectric Wizard
Posts: 1739
Joined: Sat Mar 26, 2016 3:48 pm
Model of CNC Machine: Shark HD3 Pro Extended Bed with Spindle
Contact:

Re: Easy Organizer Maker gadget

Post by sharkcutup »

Be sure to create Proper Material size and that it is TWO_SIDED for there is a material sheet created that is a two-sided carving. You will find out very quickly though that there is an error pop-up message that will appear when trying to start the gadget if you don't have the project setup as TWO_SIDED drawing.

Sharkcutup
hoganscnccrafts.com
V-Carve Help is Available!!!
PM me or Visit my website!
V-Carve Pro 11.016

User avatar
jimandi5000
Vectric Wizard
Posts: 876
Joined: Wed Mar 11, 2015 6:50 pm
Model of CNC Machine: Home Made 60 x 120
Location: North Houston Tx.
Contact:

Re: Easy Organizer Maker gadget

Post by jimandi5000 »

Hello All,

I have updated the code to address the endless error trapping loop on attempting to clear a preselected tool issue. The solution will allow you to select tools for the Dado or Finger clearing path that are of the same bit diameter or smaller than the primary tool. You will be presented a message box (see below) and the solution will step over the issue and produce the drawing and toolpaths correctly.
Additional error trapping has been added and the optimization of code.

This Version 1.5

Supports: 11.0 and up

Installation Instructions
1. Download the gadget EasyOrganizerMaker.zip that is attached to this post.
2. Rename it from EasyOrganizerMaker.zip to EasyOrganizerMaker.vgadget
3. In Vectric Pro or Aspire click on Gadgets -> Install Gadget and navigate to where you downloaded the file to, select it and click Ok.

Will be presented a pop message up saying the gadget was installed and you should see the new version of EasyOrganizerMaker in the Gadgets menu.
Attachments
EasyOrganizerMaker.zip
(39.96 KiB) Downloaded 60 times
Messages1.png
Messages2.png
Thanks,
Jim

Post Reply