This was a quick and easy project.
My daughter has an English Mastiff, so I found silhouette clipart and did a Zank-inlay on the backside of a 7" x 10" x 0.325" bamboo cutting board that I picked up at a Target department store. The inlay material is east indian rosewood that was 0.18" thick. It was in an assortment pack of guitar headplate samples. I used a CMT 60° V-bit with a flat depth of 0.15", and a 1/4" endmill for the clearance areas. I glued it overnight with original Titebond glue and sprayed it with a water-based poly finish.
Mastiff Silhouette Cutting Board using Zank Inlay
- Rcnewcomb
- Vectric Archimage
- Posts: 5919
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Mastiff Silhouette Cutting Board using Zank Inlay
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
- gkas
- Vectric Wizard
- Posts: 1451
- Joined: Sun Jan 01, 2017 3:39 am
- Model of CNC Machine: Aspire, Axiom AR8 Pro+, Axiom 4.2W Laser
- Location: Southern California
Re: Mastiff Silhouette Cutting Board using Zank Inlay
Nice... I never thought about doing an inlay in something that thin. Stuff to ponder.
- Tex_Lawrence
- Vectric Wizard
- Posts: 958
- Joined: Fri Mar 25, 2016 11:30 am
- Model of CNC Machine: Shapeoko3XXL; JTech7W; V-CarvePro 12.004
- Location: Dayton, Texas (Don't Mess With My Texas!)
Re: Mastiff Silhouette Cutting Board using Zank Inlay
Tell them to be careful with that thin bamboo board. One time I ran across some like it in WalMart both 1/4" and 3/8". I had the thought to see if they were so thin they would actually flex. Well, the 3/8" one did flex ... to the point of breaking ... SNAP! (The management didn't want to prosecute me. )
Perhaps it was a defective product.
Perhaps it was a defective product.
Tex — Crooked Wood Products
Now there's a man with an open mind – you can feel the breeze from here.
Now there's a man with an open mind – you can feel the breeze from here.
- scotttarnor
- Vectric Wizard
- Posts: 944
- Joined: Fri Aug 30, 2019 11:40 pm
- Model of CNC Machine: Piranha XL , Shark HD520
- Location: La Crosse WI
Re: Mastiff Silhouette Cutting Board using Zank Inlay
Nice looking cutting board!
Scott T
@scottscnc
@scottscnc
- scottp55
- Vectric Wizard
- Posts: 4717
- Joined: Thu May 09, 2013 11:30 am
- Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP11.5
- Location: Kennebunkport, Maine, US
Re: Mastiff Silhouette Cutting Board using Zank Inlay
Nice Randall!!
I've used scraps of button runs at .22-.235" at .2" flat depth... .18" is nice to know:)
Using my remaining EI Rosewood from '95 Very sparingly nowadays!!
Pretty!!
scott
I've used scraps of button runs at .22-.235" at .2" flat depth... .18" is nice to know:)
Using my remaining EI Rosewood from '95 Very sparingly nowadays!!
Pretty!!
scott
I've learned my lesson well. You can't please everyone,so you have to please yourself
R.N.
R.N.
-
- Vectric Wizard
- Posts: 520
- Joined: Sun May 03, 2015 12:25 pm
- Model of CNC Machine: Axiom AR8
- Location: Savannah, GA
Re: Mastiff Silhouette Cutting Board using Zank Inlay
Nice clean cut and the grain patterns compliment.
-
- Vectric Craftsman
- Posts: 216
- Joined: Tue Jun 12, 2018 3:07 pm
- Model of CNC Machine: Axiom AR 8 Pro+
- Location: Cambria, CA
Re: Mastiff Silhouette Cutting Board using Zank Inlay
That’s a very nice board, Randall! A note to consider for future inlays with thin, precious wood samples...if you need to use every last hundredth of an inch of the thickness of your male stock for an inlay you can first back it with 1/8” - 1/4” birch plywood or melamine or mdf—any kind of cheap waste board that you can laminate to your precious stock. I do that pretty commonly anyway, even with 1/4” male stock, to stabilize the male workpiece during carving.
-
- Vectric Wizard
- Posts: 409
- Joined: Thu Apr 06, 2017 3:07 am
- Model of CNC Machine: Camaster Stinger SR24
- Location: Addison, PA
Re: Mastiff Silhouette Cutting Board using Zank Inlay
Thats a clever idea, thanks for sharing!!laflippin wrote: ↑Sun Dec 27, 2020 5:27 pmThat’s a very nice board, Randall! A note to consider for future inlays with thin, precious wood samples...if you need to use every last hundredth of an inch of the thickness of your male stock for an inlay you can first back it with 1/8” - 1/4” birch plywood or melamine or mdf—any kind of cheap waste board that you can laminate to your precious stock. I do that pretty commonly anyway, even with 1/4” male stock, to stabilize the male workpiece during carving.
Beautiful inlay work, Randall.
Joe
I have a chip on my shoulder....several more in my hair and lots more all over my shop floor.
I have a chip on my shoulder....several more in my hair and lots more all over my shop floor.