Page 1 of 1
A little something
Posted: Fri Jul 17, 2020 12:27 am
by Makingtoothpicks
Something I am working on. I have a redesigned it. Practicing my non artistic abilities.
Thank You for looking
Don
Re: A little something
Posted: Fri Jul 17, 2020 12:45 am
by TReischl
Looks good!
A very unique finish that makes it look really, REALLY old, nicely done.
Re: A little something
Posted: Fri Jul 17, 2020 12:50 am
by Leo
??????? non-artistic ???????
NOT from where I am standing
That is superior ability
Fantastic job.
Re: A little something
Posted: Fri Jul 17, 2020 3:59 am
by mtylerfl
Nice job, Don! “Old-World” finish effect!
Re: A little something
Posted: Fri Jul 17, 2020 2:49 pm
by Tex_Lawrence
Ditto on what others have posted! I really thought you were somehow over-carving a cast piece.
FYI, (not to take away from your art) that Vbit cut on-the-line around the perimeter could use a bit of offset to the outside (or the point is broken). I noticed because that started happening to my cuts.
Nice, very nice! +1
Re: A little something
Posted: Fri Jul 17, 2020 4:17 pm
by rgerding
Very nice. Is the material corian or something like it?
Ron
Re: A little something
Posted: Fri Jul 17, 2020 5:16 pm
by GeneMpls
Very nice, I use a lot of corian [and similar] on both the CNC and CO2 laser.
Re: A little something
Posted: Fri Jul 17, 2020 9:40 pm
by Makingtoothpicks
Yes it is Corian or something like it. It was a cut off and given to me.
Re: A little something
Posted: Fri Jul 17, 2020 9:43 pm
by Makingtoothpicks
Tex_Lawrence wrote: ↑Fri Jul 17, 2020 2:49 pm
Ditto on what others have posted! I really thought you were somehow over-carving a cast piece.
FYI, (not to take away from your art) that Vbit cut on-the-line around the perimeter could use a bit of offset to the outside (or the point is broken). I noticed because that started happening to my cuts.
Nice, very nice! +1
I am not sure what you are referring to. The outside profile cut was a straight end mill. The only place I used a V-bit was the text.
tools used 1/16 tapered ball nose , 1/8 end mill ,90 deg V bit
Don
Re: A little something
Posted: Sat Jul 18, 2020 1:34 pm
by Tex_Lawrence
What I was referring to was the small edge Vee around the profile. Perhaps this was intentional? Not trying to be picky; just interested.
Re: A little something
Posted: Sat Jul 18, 2020 2:53 pm
by Holzarbeiter
Your artistic abilities are commendable. Excellent job. I love the look of the finish. I also love working with Corian.
Re: A little something
Posted: Sat Jul 18, 2020 7:23 pm
by Makingtoothpicks
Tex_Lawrence wrote: ↑Sat Jul 18, 2020 1:34 pm
What I was referring to was the small edge Vee around the profile. Perhaps this was intentional? Not trying to be picky; just interested.
EdgeGroove.png
You are not being picky. I appreciate your input. It was not intentional. This was a test so I could see what
needs improving. On my next one a will look closer at that.
Thank You
Don
Re: A little something
Posted: Sun Jul 19, 2020 11:31 am
by bravesoul1950
That looks great, wish I had your abilities but at my old age I will just muddle through with simpler items.
Joe