Does it matter what side of the 4th axis that you cut on?
-
- Vectric Apprentice
- Posts: 99
- Joined: Sun Sep 06, 2015 2:49 am
- Model of CNC Machine: Shark HD3
Does it matter what side of the 4th axis that you cut on?
On my CNC's 4th axis I cut from the top; however, I was thinking of using some profile cutters that will cut from the side. So I was wondering if it matters on what side of the headstock you place the router on because of how the router is spinning?
-
- Vectric Apprentice
- Posts: 59
- Joined: Wed Sep 18, 2019 2:05 am
- Model of CNC Machine: laguna 4x8 w/ 11" 4th Axis; MX CO2 laser
- Location: Calgary, AB
Re: Does it matter what side of the 4th axis that you cut on?
I thought about this when I don't have room above the workpiece for a bit.
Cutting from the side places the bit at an angle to the work piece rather than perpendicular. This will impact the Z axis up/down movement relative to the model and will impact any profile that you are trying to cut. Geometrically; the Z(offset) movement will become the sin(offset angle)*Z.
Visually, the plunge in the Z direction will look odd. I do not think Aspire can model offsets.
Mechanically, the bit will always have a sideload. Small diameter bits will ultimately fail.
But if you are not modeling and just cutting on a vector, I would use a climb cut to minimize chipping. Let me know how it goes.
Cutting from the side places the bit at an angle to the work piece rather than perpendicular. This will impact the Z axis up/down movement relative to the model and will impact any profile that you are trying to cut. Geometrically; the Z(offset) movement will become the sin(offset angle)*Z.
Visually, the plunge in the Z direction will look odd. I do not think Aspire can model offsets.
Mechanically, the bit will always have a sideload. Small diameter bits will ultimately fail.
But if you are not modeling and just cutting on a vector, I would use a climb cut to minimize chipping. Let me know how it goes.
- rscrawford
- Vectric Wizard
- Posts: 1104
- Joined: Mon Jan 17, 2011 6:49 pm
- Model of CNC Machine: CAMaster Cobra 408 ATC, ShopSabre IS408
- Location: Wetaskiwin, Alberta
- Contact:
Re: Does it matter what side of the 4th axis that you cut on?
I replaced my 4th axis with a lathe and I always cut from the side with a 1/2" downcut endmill. I turn the lathe at 300rpm and have it turning up into my cutter (so the downcut edge sheers the wood like a regular knife would). I spin the end mill at 18000rpm and usually have a feed speed of 10ipm. I can turn a 2" square blank into a french rolling pin with a single pass in 2 minutes, with a finish that rivals a knife cut. Just another 30 seconds each of 220, 400 and 600 grit sanding.
Russell Crawford
http://www.cherryleaf-rustle.com
http://www.cherryleaf-rustle.com
-
- Vectric Wizard
- Posts: 1261
- Joined: Sun Jan 11, 2009 4:30 am
- Model of CNC Machine: 2014 roc-tech 4x8 with servos
- Location: bridgeton, indiana
Re: Does it matter what side of the 4th axis that you cut on?
sweet
http://www.3dsigncamp.com
http://www.roctechusacnc.com
http://www.roctechusacnc.com
-
- Vectric Craftsman
- Posts: 185
- Joined: Thu May 14, 2015 12:29 am
- Model of CNC Machine: AVID PRO-Acorn , Shapeoko SO3 XXL & SO3s
- Location: Colorado
- Contact:
Re: Does it matter what side of the 4th axis that you cut on?
What is the difference between a 4th axis and a lathe?
- rscrawford
- Vectric Wizard
- Posts: 1104
- Joined: Mon Jan 17, 2011 6:49 pm
- Model of CNC Machine: CAMaster Cobra 408 ATC, ShopSabre IS408
- Location: Wetaskiwin, Alberta
- Contact:
Re: Does it matter what side of the 4th axis that you cut on?
A lathe spins freely, no indexing (well, they usually have 24 or 36 indexing holes to hold your workpiece in place in those increments).ElevationCreations wrote: ↑Tue Feb 02, 2021 2:34 amWhat is the difference between a 4th axis and a lathe?
A 4th axis is run by a stepper motor (or servo) and turns incrementally.
Russell Crawford
http://www.cherryleaf-rustle.com
http://www.cherryleaf-rustle.com
- sawmiller
- Vectric Wizard
- Posts: 531
- Joined: Sat May 03, 2008 8:34 pm
- Model of CNC Machine: joe's rack and pinion hybrid
- Location: camden,tn
Re: Does it matter what side of the 4th axis that you cut on?
So russel, do you use a modified post-processer that maybe ignores the a commands?
woodmizer sawmill and joe's hybrid cnc, a good combination
In the heart of Tn
In the heart of Tn
- Leo
- Vectric Wizard
- Posts: 4091
- Joined: Sat Jul 14, 2007 3:02 am
- Model of CNC Machine: 1300 x 1300 x 254 Chinese Made
- Location: East Freetown, Ma.
- Contact:
Re: Does it matter what side of the 4th axis that you cut on?
When I was working in the industry I wrote G-Code for machining centers. A CNC router is essentially a machining center. When I wrote programs for a rotary axis it did not matter how I approached the workpiece. HOWEVER, experience teaches that the toolpath that is being programmed IS of consequence. HOW - you program the toolpath is what makes all the difference.
You can break a 1 inch diameter end mill just as easily as a 1/8 keyslot cutter or a 1/16 drill. I know this from experience.
Lathe = generally a spinning spindle with an "X" and "Z" axis.
Rotary axis = An axis added to a 3 axis machine to allow a rotating, but not "spinning" axis. It CAN be used as an Indexer. This is a 4-th axis where all 4 axis's can be used simultaneously, IF, the rotation axis has drivers built is to the control as apposed to axis swapping. Drive motors can be stepper OR servo.
Indexer = an axis added to a 3 axis machine to allow Specific degrees of rotation, but not a rotating axis. All 4 axis motions cannot be cutting simultaneously.
There is always an exception to any rule but they are not commonplace.
You can break a 1 inch diameter end mill just as easily as a 1/8 keyslot cutter or a 1/16 drill. I know this from experience.
Lathe = generally a spinning spindle with an "X" and "Z" axis.
Rotary axis = An axis added to a 3 axis machine to allow a rotating, but not "spinning" axis. It CAN be used as an Indexer. This is a 4-th axis where all 4 axis's can be used simultaneously, IF, the rotation axis has drivers built is to the control as apposed to axis swapping. Drive motors can be stepper OR servo.
Indexer = an axis added to a 3 axis machine to allow Specific degrees of rotation, but not a rotating axis. All 4 axis motions cannot be cutting simultaneously.
There is always an exception to any rule but they are not commonplace.
Imagine the Possibilities of a Creative mind, combined with the functionality of CNC
- IslaWW
- Vectric Wizard
- Posts: 1403
- Joined: Wed Nov 21, 2007 11:42 pm
- Model of CNC Machine: CNC Controller Upgrades
- Location: Bergland, MI, USA
Re: Does it matter what side of the 4th axis that you cut on?
I have built a few lathe based machines that use a servo motor and a specialized servo drive that can do both positional (4th axis rotary) and velocity (lathe type spinning) control. They may seem to be nearly the same action to the occasional user, but in fact, they are drastically different, as Leo can attest to. I do not know of a single design software that can produce toolpaths for both well due to the "different" coordinate systems used.
Like Leo says, on a lathe left/right is the Z axis and in/out is X. Rotation speed is handled via analog voltage. On a rotary 4th axis left/right is X or Y, in/out (up/down) is Z and rotation is A or B and is given as positional degrees.
To accomplish side cutting well you must provide a fairly powerful constant rotation. Quality cuts are easily attainable as Russell states above. That said, details may be hard to develop as you are limited to the radius of the bit.
These types of "out of the box" are not for the casual user. It takes a good bit of machine knowledge and some hand programming like the Leo's of the world, and you need to match it with the machine savvy like the Russell's of the world and combine it with some open minded, not in the manual, Vectric design trickery. But it can be done if you put your mind to it.
The rotary stuff seems to have tapered down to very few postings over the last few years. In the hopes of encouraging some new guys/gals into taking the plunge and provide some examples of what you can do with Vectric software (all done with VCPro), look over my rotary videos starting about 7 years back: https://www.youtube.com/user/Islaww1/videos
Like Leo says, on a lathe left/right is the Z axis and in/out is X. Rotation speed is handled via analog voltage. On a rotary 4th axis left/right is X or Y, in/out (up/down) is Z and rotation is A or B and is given as positional degrees.
To accomplish side cutting well you must provide a fairly powerful constant rotation. Quality cuts are easily attainable as Russell states above. That said, details may be hard to develop as you are limited to the radius of the bit.
These types of "out of the box" are not for the casual user. It takes a good bit of machine knowledge and some hand programming like the Leo's of the world, and you need to match it with the machine savvy like the Russell's of the world and combine it with some open minded, not in the manual, Vectric design trickery. But it can be done if you put your mind to it.
The rotary stuff seems to have tapered down to very few postings over the last few years. In the hopes of encouraging some new guys/gals into taking the plunge and provide some examples of what you can do with Vectric software (all done with VCPro), look over my rotary videos starting about 7 years back: https://www.youtube.com/user/Islaww1/videos
Gary Campbell
GCnC Control
ATC & Servo Controller Controller Upgrades
GCnC411 (at) gmail.com
GCnC Control
ATC & Servo Controller Controller Upgrades
GCnC411 (at) gmail.com
- sawmiller
- Vectric Wizard
- Posts: 531
- Joined: Sat May 03, 2008 8:34 pm
- Model of CNC Machine: joe's rack and pinion hybrid
- Location: camden,tn
Re: Does it matter what side of the 4th axis that you cut on?
Gary, i have been following your videos for several years, and i have made a separate cnc lathe machine, not very well, but it works.
My big question is programming the shape of table legs and rolling pins using aspire as the design software vs a hodgepodge of free software combined with manual tweaks. For example, setting pass depth.
On my lathe cnc i only have one knife instead of being able to switch out as you do for finishing
My big question is programming the shape of table legs and rolling pins using aspire as the design software vs a hodgepodge of free software combined with manual tweaks. For example, setting pass depth.
On my lathe cnc i only have one knife instead of being able to switch out as you do for finishing
woodmizer sawmill and joe's hybrid cnc, a good combination
In the heart of Tn
In the heart of Tn
- Leo
- Vectric Wizard
- Posts: 4091
- Joined: Sat Jul 14, 2007 3:02 am
- Model of CNC Machine: 1300 x 1300 x 254 Chinese Made
- Location: East Freetown, Ma.
- Contact:
Re: Does it matter what side of the 4th axis that you cut on?
When I said there are exceptions to every rule - I was thinking of Gary. He builds some incredible stuff. I truly wish I could have his machine, but I am already invested in what I have. I think Gary calls it a sidewinder? To my mind - Gary is UP there.
Imagine the Possibilities of a Creative mind, combined with the functionality of CNC
- IslaWW
- Vectric Wizard
- Posts: 1403
- Joined: Wed Nov 21, 2007 11:42 pm
- Model of CNC Machine: CNC Controller Upgrades
- Location: Bergland, MI, USA
Re: Does it matter what side of the 4th axis that you cut on?
I have never (literally never) used any freeware so I can't answer your question. In my experience, the more I've paid for specialty software, the more I've liked it.sawmiller wrote: ↑Thu May 05, 2022 3:59 pmGary, i have been following your videos for several years, and i have made a separate cnc lathe machine, not very well, but it works.
My big question is programming the shape of table legs and rolling pins using aspire as the design software vs a hodgepodge of free software combined with manual tweaks. For example, setting pass depth.
On my lathe cnc i only have one knife instead of being able to switch out as you do for finishing
As far as multi pass lathe design goes, I start with the profile I desire, add lead in and out, then use the offset tool to create the multiples. Select them in order and you're ready to cut.
Gary Campbell
GCnC Control
ATC & Servo Controller Controller Upgrades
GCnC411 (at) gmail.com
GCnC Control
ATC & Servo Controller Controller Upgrades
GCnC411 (at) gmail.com
-
- Vectric Apprentice
- Posts: 53
- Joined: Mon Jul 19, 2021 9:14 pm
- Model of CNC Machine: AvidCNC
Re: Does it matter what side of the 4th axis that you cut on?
Here is an example of a leg for a Victorian Style Wash Stand.
https://drive.google.com/file/d/1EPo_RZ ... sp=sharing
Please try it out. It has also the Mortises already included.https://drive.google.com/file/d/1EPo_RZ ... sp=sharing
-
- Vectric Craftsman
- Posts: 113
- Joined: Fri Jun 06, 2014 7:01 am
- Model of CNC Machine: ShopBot PRSalpha, custom rotary indexer
- Location: Tucson, Arizona
Re: Does it matter what side of the 4th axis that you cut on?
Here is a link to one of my posts from several years ago where Gary Campbell made the gear reduction/Stepper motor modification for my lathe.
viewtopic.php?f=18&t=21487&p=152680#top
viewtopic.php?f=18&t=21487&p=152680#top