hi Guys
I would like to make a polygon with the rotation axis
To do this, you would have to be able to address all 4 axes because otherwise it would be rather inefficient with a drawn fillet to take the rotation into account for a flat surface
I have done it once before and have turned the axle by hand, but this is very time consuming for larger quantities
Is there an additional program to control all axes in one step?
regards Richard
a way to use 4 axis on rotary

 Posts: 7
 Joined: Thu Nov 30, 2017 11:02 pm
 Model of CNC Machine: 9015(35,43x59,06 inch) cnc router
 Location: Austria
 rscrawford
 Vectric Wizard
 Posts: 977
 Joined: Mon Jan 17, 2011 6:49 pm
 Model of CNC Machine: CAMaster Cobra 408 ATC, ShopSabre IS408
 Location: Wetaskiwin, Alberta
 Contact:
Re: a way to use 4 axis on rotary
I would just edit your Gcode and add the rotation and copy and paste the 'pocket' tool path that cuts each face for each rotation until you are done.
Russell Crawford
http://www.cherryleafrustle.com
http://www.cherryleafrustle.com

 Posts: 7
 Joined: Thu Nov 30, 2017 11:02 pm
 Model of CNC Machine: 9015(35,43x59,06 inch) cnc router
 Location: Austria
Re: a way to use 4 axis on rotary
I'll try it out on the next project......

 Vectric Wizard
 Posts: 1327
 Joined: Sun Sep 23, 2012 12:14 pm
 Model of CNC Machine: CNC Shark Pro, Probotix Meteor 25" x 50"
Re: a way to use 4 axis on rotary
Using Aspire or Vcarve there is no way to directly control all 4 axes in the same file. To make a polygon though you can use the moulding toolpath and a little drafting to come up with a vector path for the moulding toolpath to follow. I've posted an octagonal shape in another thread here. In this post below is a 5sided polygon extrusion cut from a 1.5" dowel. Basically start with a circle the diameter of your blank, then draw the polygon shape you want made inside the circle. The distance between the center of each flat face of the polygon and the circle is how deep a curve needs to be that gets stretched across the material block. You are essentially unfolding the circle perimeter with the polygon faces remaining the same distance from the circle. All vectors used in the Aspire file attached. Version 9.519.
4D Attachments

 5sided rotary moulding.crv3d
 (119 KiB) Downloaded 22 times
Re: a way to use 4 axis on rotary
Since Aspire v9.5 there is a builtin vector unwrapper. This tool can be used in connection with moulding toolpath or tworail sweep. When using this tool is no need to draw a circle. Just draw a desired polygon and select 'Vector Unwrapper'.
The tool will display a circle with the same diameter as the job. Once polygon is positioned in the middle, it can be easily resized to fit the circle (holding shift while resizing is recommended). The click 'Apply' and the tool will create a curve.
This curve can be used directly with the moulding toolpath.
Greg K
The tool will display a circle with the same diameter as the job. Once polygon is positioned in the middle, it can be easily resized to fit the circle (holding shift while resizing is recommended). The click 'Apply' and the tool will create a curve.
This curve can be used directly with the moulding toolpath.
Greg K

 Vectric Wizard
 Posts: 1327
 Joined: Sun Sep 23, 2012 12:14 pm
 Model of CNC Machine: CNC Shark Pro, Probotix Meteor 25" x 50"
Re: a way to use 4 axis on rotary
Thanks for point out the vector unwrapping tool, gregk. I hadn't noticed that before. I used it to duplicate what I did in my previous post and found a few significant differences in the results.
First is that the moulding result has slight concave curves in the faces that the original vector polygon did not have.
Secondly the created curves aren't curves but rather a bunch of closely spaced vectors with legs that aren't needed for the moulding toolpath. . Yes I know the legs are easily deleted and the lines can be turned into simpler arcs.
Thirdly the result also looks to be making a shape that isn't centered in the stock.
Again my file is from Aspire 9.519.
4D
First is that the moulding result has slight concave curves in the faces that the original vector polygon did not have.
Secondly the created curves aren't curves but rather a bunch of closely spaced vectors with legs that aren't needed for the moulding toolpath. . Yes I know the legs are easily deleted and the lines can be turned into simpler arcs.
Thirdly the result also looks to be making a shape that isn't centered in the stock.
Again my file is from Aspire 9.519.
4D
 Attachments

 vector unwrapped 4D.crv3d
 (101.5 KiB) Downloaded 18 times
Re: a way to use 4 axis on rotary
This is most likely an issue of numerical accuracy. And I can also see this slight concavity with your vectors4DThinker wrote:Thanks for point out the vector unwrapping tool, gregk. I hadn't noticed that before. I used it to duplicate what I did in my previous post and found a few significant differences in the results.
First is that the moulding result has slight concave curves in the faces that the original vector polygon did not have.
You can try ticking 'Simplify unwrapped vectors' option (or use Curve Fit afterwards as this gives more control). However, as far as moulding toolpath is concerned, this doesn't really matter as the toolpath will polygonise those curves internally.4DThinker wrote: Secondly the created curves aren't curves but rather a bunch of closely spaced vectors with legs that aren't needed for the moulding toolpath. . Yes I know the legs are easily deleted and the lines can be turned into simpler arcs.
4D
I wouldn't remove the legs, as they help to ensure that the toolpath is positioned accurately in z. If that distance is adjusted, the result will be a polygon with rounded sides.
Of course if the material have the exact same diameter as the polygon and the gap above toolpath is set to 0, the results will be accurate. But if you decide to make this polygon slightly smaller, then with legs you can just need to ensure that gap below toolpath is 0.
Without legs you will need to be more careful with positioning the toolpath.
I hope that this makes sense.
Greg K

 Vectric Wizard
 Posts: 1327
 Joined: Sun Sep 23, 2012 12:14 pm
 Model of CNC Machine: CNC Shark Pro, Probotix Meteor 25" x 50"
Re: a way to use 4 axis on rotary
The tiny arc in my first 5sided example is easily corrected by changing the height of my curve row that made the extrusion. Mathematically the faces should be flat but the slight curve may be due to the shape of the ball nose bit and it's approach to the face as the angle changes.
With the legs left on of the unwrapping tool vectors an error is generated that prevents the moulding tool from finishing. "Cut Depth Exceeds Thickness!".
The generated vectors rise up in the middle and in theory should be a flat row. Another flaw in the calculation which is what results in an offcenter cut.
The unwrapping tool may produce better unwrapped results with different shapes, but as is I wouldn't trust it to create accurate vectors for the moulding toolpath on simple flat faced polygons.
4D
With the legs left on of the unwrapping tool vectors an error is generated that prevents the moulding tool from finishing. "Cut Depth Exceeds Thickness!".
The generated vectors rise up in the middle and in theory should be a flat row. Another flaw in the calculation which is what results in an offcenter cut.
The unwrapping tool may produce better unwrapped results with different shapes, but as is I wouldn't trust it to create accurate vectors for the moulding toolpath on simple flat faced polygons.
4D
Re: a way to use 4 axis on rotary
Keep in mind that the unwrapper tool allows you to pick the centre of the polygon, so you can create 'off centre' polygons if you want:
Using center of vector's bounding box  results in profile being slightly offcentre Using the actual center of the shape This tool was specifically developed with simple polygons in mind. And I can trust its results since I spend quite some time developing this and other rotary features
But I understand that if you did the math yourself and understand the whole process, you may feel more comfortable with your solution rather than some black box.
In any case, thanks for you contribution into wrapped rotary machining!
Greg K
Using center of vector's bounding box  results in profile being slightly offcentre Using the actual center of the shape This tool was specifically developed with simple polygons in mind. And I can trust its results since I spend quite some time developing this and other rotary features
But I understand that if you did the math yourself and understand the whole process, you may feel more comfortable with your solution rather than some black box.
In any case, thanks for you contribution into wrapped rotary machining!
Greg K

 Vectric Wizard
 Posts: 1327
 Joined: Sun Sep 23, 2012 12:14 pm
 Model of CNC Machine: CNC Shark Pro, Probotix Meteor 25" x 50"
Re: a way to use 4 axis on rotary
Yep. I should spend more time with a new (to me) feature before drawing a conclusion about its usefulness. That centering option I didn't notice since I started with a circle the diameter of my blank. I've been challenging this tool with all sorts of shapes since I last posted and have found it does a good job most of the time once I've centered the shape using that option. From triangles to ellipses to bumpy mutations all seemed to work unless the result would have undercuts if done on a rotary axis. Polygons with an odd number of sides don't automatically get centered even if they "look" centered in the circles I've drawn them in. The slight curve in what should be flat faces is so small when cut that it sands flat easily.
As always Aspire continues to amaze me with the great drafting tools and features. I often use the measure tool to help students calculate spacing for kerf cuts in plywood they want to bend, and many cases where precision dimensions are needed on complex shapes. My students have other drafting software that "should" be able to help them come up with the same answers, but are usually impressed with how direct/simple/obvious the features are in Aspire that gets them the answers they need.
4D
As always Aspire continues to amaze me with the great drafting tools and features. I often use the measure tool to help students calculate spacing for kerf cuts in plywood they want to bend, and many cases where precision dimensions are needed on complex shapes. My students have other drafting software that "should" be able to help them come up with the same answers, but are usually impressed with how direct/simple/obvious the features are in Aspire that gets them the answers they need.
4D