Help please;
VCarve Pro
So I have been learning some CAD software and can draw and export 3D models. I export in the .STL formal. These go into VCarve Pro just fine, looking just like they should, correct dimensions come over, correct orientation etc. However I cannot, regardless of all the permutations of model depth, z-plane, zero plane, vector positioning, I believe in fact, I have played with every available VCarve variable in this area and I cannot get the Z depth to where the whole depth of the model is cut out. I can do it with the VCarve clip art, but not with any object I have drawn and imported.
Any takers on a solution for me?
This is what Vectric promises on import....
What's not to like? The model is all as it was drawn in my CAD
Same again, with the basic settings; I have varied all of these to no avail....
But wait, look at the toolpath, it has a ledge, in this case it is about 4mm out of a 40 mm deep model:
Run the simulation and there is the ledge in all its glory:
How do I get my 40 mm in Z model to be machined at 40 mm? I have imported a number of tests and they all experience the same problem. As noted, I have tried every variation of planes, model in the material, slicing, Z heights etc to no avail.
Any takers on a solution for me. ?
3D Machining Depth Never Correct
-
- Posts: 9
- Joined: Fri Feb 07, 2020 12:46 am
- Model of CNC Machine: AccTek
- SteveNelson46
- Vectric Wizard
- Posts: 2310
- Joined: Wed Jan 04, 2012 2:43 pm
- Model of CNC Machine: Camaster Stinger 1
- Location: Tucson, Az.
Re: 3D Machining Depth Never Correct
If you look closer at the toolpath then you can notice that it stops when it reaches material boundaries. In order to machine your shape the tool have to go outside of your material boundaries. You need to make your material bigger, otherwise tool will not be allowed to machine whole model. Hope this make sense,
Greg K
Greg K
-
- Vectric Craftsman
- Posts: 253
- Joined: Fri May 09, 2014 1:37 pm
- Model of CNC Machine: Laguna IQ
- Location: Pensacola FL
Re: 3D Machining Depth Never Correct
Have a look at this thread. I think you are having the same problem.
viewtopic.php?f=27&t=24723&p=177179&hil ... et#p177138
viewtopic.php?f=27&t=24723&p=177179&hil ... et#p177138
-
- Posts: 9
- Joined: Fri Feb 07, 2020 12:46 am
- Model of CNC Machine: AccTek
Re: 3D Machining Depth Never Correct
Thanks to all who have answered:
I have always used a zero plane and played with where it is located;
I have increased the vector offset around the model to no apparent avail;
However, although I have played with various material depth settings, I am not sure I have tried to "pretend" the model is thicker than it actually is, I will run off and try that now.
I have always used a zero plane and played with where it is located;
I have increased the vector offset around the model to no apparent avail;
However, although I have played with various material depth settings, I am not sure I have tried to "pretend" the model is thicker than it actually is, I will run off and try that now.
- Adrian
- Vectric Archimage
- Posts: 14680
- Joined: Thu Nov 23, 2006 2:19 pm
- Model of CNC Machine: ShopBot PRS Alpha 96x48
- Location: Surrey, UK
Re: 3D Machining Depth Never Correct
I created a model like yours and had the same issue. I added a zero plane and recalculated the toolpaths and it was fine.
- adze_cnc
- Vectric Wizard
- Posts: 4379
- Joined: Sat Jul 27, 2013 10:08 pm
- Model of CNC Machine: AXYZ 4008
- Location: Vancouver, BC, Canada
Re: 3D Machining Depth Never Correct
Adrian,
Was your model "bounding box" XY dimensions the same as the job size XY dimensions when you added the zero-plane?
I also made a test model like this then added a zero plane but since the base model size and the job size were the same the zero-plane didn't matter as it was that same size. I just can't really see how adding zero-plane can help on a convex model unless the job size is larger than the model size so that the zero plane extends the model. Then you can use the "model boundary" setting in the 3D finish path.
My general approach to any of these type models is to create a 3D finish path with a "selected vector" which is the profile of the 3D model. I then use the boundary offset to force the bit to cut to the bottom of the vertical curve plane. I just need to plan things so that the finish path doesn't "go over the edge" on the vertical ends--usually making the boundary vector shorter by the boundary offset on those ends.
Steven
Was your model "bounding box" XY dimensions the same as the job size XY dimensions when you added the zero-plane?
I also made a test model like this then added a zero plane but since the base model size and the job size were the same the zero-plane didn't matter as it was that same size. I just can't really see how adding zero-plane can help on a convex model unless the job size is larger than the model size so that the zero plane extends the model. Then you can use the "model boundary" setting in the 3D finish path.
My general approach to any of these type models is to create a 3D finish path with a "selected vector" which is the profile of the 3D model. I then use the boundary offset to force the bit to cut to the bottom of the vertical curve plane. I just need to plan things so that the finish path doesn't "go over the edge" on the vertical ends--usually making the boundary vector shorter by the boundary offset on those ends.
Steven
-
- Posts: 9
- Joined: Fri Feb 07, 2020 12:46 am
- Model of CNC Machine: AccTek
Re: 3D Machining Depth Never Correct
SOLVED:
Thanks for those who kindly replied. I managed to solve this by NOT selecting "centre model" option you get in the initial dialog box that pops up when you import a 3d file from other than the clipart. Centring the plane in the middle of the model seems to be the issue.
So oddly, without doing any centring options, when I click out of the import 3d model dialogue box, the model seems to centre itself anyway.
I am posting this for others in the off chance they have the same issue.
In summary, load up your model, touch nothing but the orientation and then get out of the import model section. Run your tool path with the offset set at 0.5 of the diameter of the tool used and it will cut to the correct level.
Thanks for those who kindly replied. I managed to solve this by NOT selecting "centre model" option you get in the initial dialog box that pops up when you import a 3d file from other than the clipart. Centring the plane in the middle of the model seems to be the issue.
So oddly, without doing any centring options, when I click out of the import 3d model dialogue box, the model seems to centre itself anyway.
I am posting this for others in the off chance they have the same issue.
In summary, load up your model, touch nothing but the orientation and then get out of the import model section. Run your tool path with the offset set at 0.5 of the diameter of the tool used and it will cut to the correct level.