I'm making a viewing window in a control
box. I want to glue two pieces of plexi glass
together (one on top of the other). What glue
do you guys use??
Thanks
olf20 / Bob
Gluing Plexi Glass
Gluing Plexi Glass
Heat with corn, Mach3, Bridgeport clone, VcarvePo, Photo VCarve, Craftsman Wood Lathe, Arduino Toys
- highpockets
- Vectric Wizard
- Posts: 3667
- Joined: Tue Jan 06, 2015 4:04 pm
- Model of CNC Machine: PDJ Pilot Pro
Re: Gluing Plexi Glass
Thanks for the quick reply John!
When gluing two flat pieces together to make it
thicker does the glue distort the view thru the
glued pieces??
olf20 / Bob
When gluing two flat pieces together to make it
thicker does the glue distort the view thru the
glued pieces??
olf20 / Bob
Heat with corn, Mach3, Bridgeport clone, VcarvePo, Photo VCarve, Craftsman Wood Lathe, Arduino Toys
- highpockets
- Vectric Wizard
- Posts: 3667
- Joined: Tue Jan 06, 2015 4:04 pm
- Model of CNC Machine: PDJ Pilot Pro
Re: Gluing Plexi Glass
Never tried gluing two thin pieces together to make a thicker piece. The glue is crystal clear so if you make sure the piece is completely covered and no bubbles, it might work.
John
Maker of Chips
Maker of Chips
- mtylerfl
- Vectric Archimage
- Posts: 5896
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: Gluing Plexi Glass
Will the perimeter edges be concealed when the viewing panel is installed? If so, perhaps you can apply glue only around the edges to make your double-layer.
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
- highpockets
- Vectric Wizard
- Posts: 3667
- Joined: Tue Jan 06, 2015 4:04 pm
- Model of CNC Machine: PDJ Pilot Pro
Re: Gluing Plexi Glass
Micheal's suggestion might work better, but warning, don't use the Acrylic Cement on the edges, it will be wick into the Plexi and mess up the edges.
John
Maker of Chips
Maker of Chips
- mtylerfl
- Vectric Archimage
- Posts: 5896
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: Gluing Plexi Glass
Yes - maybe just some clear silicon around the outside edges would suffice (if the edges will be concealed).
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
Re: Gluing Plexi Glass
What I'm doing is using a plastic box 8 x 10 with a door on
it. I want to have a window 2 x 3 in the door of the box.
I have already cut the hole in the door and have the window
cut to size. I have already done one previously and when I
applied super glue around the edges to seal them, the plexi
glass window kind of got milky where the super glue was
applied.
My plan on this one is to cut the hole in the door and window
just like I did on the first one, but cut a larger window to put
on the inside of the door and glue the two together so I can
glue the larger window to the door on the inside and seal it.
After rethinking this I might be better off to get a thicker piece
of plexi glass and just cut the window out and leave a step
around the edge to silicone to the door.
I will experiment with gluing two pieces together just for
the experience.
Thanks for the replies and the info!
olf20 / Bob
it. I want to have a window 2 x 3 in the door of the box.
I have already cut the hole in the door and have the window
cut to size. I have already done one previously and when I
applied super glue around the edges to seal them, the plexi
glass window kind of got milky where the super glue was
applied.
My plan on this one is to cut the hole in the door and window
just like I did on the first one, but cut a larger window to put
on the inside of the door and glue the two together so I can
glue the larger window to the door on the inside and seal it.
After rethinking this I might be better off to get a thicker piece
of plexi glass and just cut the window out and leave a step
around the edge to silicone to the door.
I will experiment with gluing two pieces together just for
the experience.
Thanks for the replies and the info!
olf20 / Bob
Heat with corn, Mach3, Bridgeport clone, VcarvePo, Photo VCarve, Craftsman Wood Lathe, Arduino Toys
Re: Gluing Plexi Glass
Had some 3/8" plexi scrap. Milled the window out
done a pocket / cutout. Boom siliconed edges and
done. Really turned out great.
I was over thinking the task! But I learned some things.
Thanks for the replies!
olf20 / Bob
done a pocket / cutout. Boom siliconed edges and
done. Really turned out great.
I was over thinking the task! But I learned some things.
Thanks for the replies!
olf20 / Bob
Heat with corn, Mach3, Bridgeport clone, VcarvePo, Photo VCarve, Craftsman Wood Lathe, Arduino Toys