We Will Do This

Post by **mezalick** » Wed Mar 25, 2020 9:52 am

I just thought I would offer a 3-D model for those who are looking to cut something during this difficult time.
It's a takeoff on the classic "Rosie the Riveter" design.

Zip file attached .

Download link here.....www.amazon.com/clouddrive/share/HLTNIgt ... vDwsy67Jxu[
Be safe.

Michael

Rosie 4a reduced.zip: (2.77 MiB) Downloaded 126 times

Post by **Stephanie Downing** » Wed Mar 25, 2020 10:11 am

Hi Michael,

Thank you for sharing your model

Post by **scottp55** » Wed Mar 25, 2020 10:19 am

Thanks Michael!

scott

Post by **JoeBlow** » Wed Mar 25, 2020 12:21 pm

This is great! My wife works for the NYS Dept. of Health as a Nurse Practioner and my daughter is a RN at the VA hospital here. I see this coming in handy. Thanks so much!

Post by **mezalick** » Wed Mar 25, 2020 12:43 pm

Now I just have to find the time to cut it....LOL

Thanks for the feedback.

Michael

Post by **Phil** » Wed Mar 25, 2020 1:56 pm

Nice, thanks for the file. My wife is involved with a group in our community making cotton masks to donate.

Phil

Post by **Bob Jr** » Wed Mar 25, 2020 4:00 pm

Thank you Michael.
Your work is appreciated very much.
Bob

Post by **Bob Jr** » Wed Mar 25, 2020 4:04 pm

Dang, I just noticed I'm the one getting Phil's hammering. At least I'm wearing a hard hat!
Bob

Post by **Creation in Wood** » Wed Mar 25, 2020 4:15 pm

Thank you for sharing your model Michael

Post by **mezalick** » Thu Mar 26, 2020 8:29 am

Here's a link to the Nurse Rosie model without the words.
https://www.amazon.com/clouddrive/share ... 2eXMhWWXJw

Post by **scottp55** » Thu Mar 26, 2020 9:30 am

Thankee Sir!!

Easier to personalize for VCP users.
Stay Safe Michael!
scott

Post by **scotttarnor** » Sat Mar 28, 2020 3:02 pm

Thank You!
I will be making one for our Daughter a Nurse in Yuma Arizona.

Post by **scotttarnor** » Sun Mar 29, 2020 2:50 pm

Well I made an attempt at this, I had 3/4" pine laying around so I tried setting base height to .5 and shape height to .24, I didn't get enough detail and had some spots like one on the mask that did not cut even. I cut the rough with a .24 EM and finish with a .125 BN.
So I adjusted base height to .4 shape height to .34 and ran it again with a .03125 TBN and it came out better.
So far I have hit it with some minwax "antique maple".
I also ran into that buried dark line

Post by **mezalick** » Sun Mar 29, 2020 4:36 pm

Nice work,,,,I realize that it'll need a really small bit to get all the fine details.
Thanks for trying it out.

Michael

Post by **jarm2** » Sun Mar 29, 2020 6:14 pm

Attached is my effort with the piece. Thanks for the file. I carved it in a piece of maple with a .06" TBN bit and applied two coats of sanding sealer before painting with paint pens. I set the component height to .625" in a 1" thick piece. It carved nicely with minimal finishing. Final two coats of clear lacquer from a rattle can. Size is 8" tall. Hope you enjoy.

Vectric Customer

We Will Do This

We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This

Re: We Will Do This