Hall of Lines

This is the place to post images of work produced using Aspire
Post Reply
nicksilva
Vectric Craftsman
Posts: 295
Joined: Thu Aug 21, 2014 8:13 pm
Model of CNC Machine: ULS M300, Rockler 60th Ann. Shark
Location: Dallas, TX USA
Contact:

Hall of Lines

Post by nicksilva »

IMG_2436 (1).jpg
Broke in my 10.0 with this 3D illusion piece. 4.5” in Mesquite.
It's just a simple VCarving and would work in either Aspire or VC.
Create everyday.
"Out of my mind. Back in 5 Minutes."

User avatar
scottp55
Vectric Wizard
Posts: 3818
Joined: Thu May 09, 2013 11:30 am
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10
Location: Kennebunkport, Maine, US

Re: Hall of Lines

Post by scottp55 »

Nice piece Nick!
Though my first thought was "That would be a tough path with a wheelchair to change your mind on" :)
Thanks!
scott
"Flatness is King"
Brady W.

scott

nicksilva
Vectric Craftsman
Posts: 295
Joined: Thu Aug 21, 2014 8:13 pm
Model of CNC Machine: ULS M300, Rockler 60th Ann. Shark
Location: Dallas, TX USA
Contact:

Re: Hall of Lines

Post by nicksilva »

thank you. yeah, it should probably be River of lines, 'cause if you're caught up in the current - well you know/
"Out of my mind. Back in 5 Minutes."

User avatar
Leo
Vectric Wizard
Posts: 3080
Joined: Sat Jul 14, 2007 3:02 am
Model of CNC Machine: 1300 x 1300 x 254 Chinese Made
Location: East Freetown, Ma.
Contact:

Re: Hall of Lines

Post by Leo »

scottp55 wrote:Nice piece Nick!
Though my first thought was "That would be a tough path with a wheelchair to change your mind on" :)
Thanks!
scott
Knowing you -- I think you would get in the groove and just GO.

I don't think there is much holding you back.
Imagine the Possibilities of a Creative mind

www.leosworkshop.com

User avatar
scottp55
Vectric Wizard
Posts: 3818
Joined: Thu May 09, 2013 11:30 am
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10
Location: Kennebunkport, Maine, US

Re: Hall of Lines

Post by scottp55 »

Thanks Leo, but on this one I'd just have pick a groove and trust Nick not to take me to a waterfall or a Rabbit Hole :)
Nice 3D Delusion Nick:)
scott
"Flatness is King"
Brady W.

scott

nicksilva
Vectric Craftsman
Posts: 295
Joined: Thu Aug 21, 2014 8:13 pm
Model of CNC Machine: ULS M300, Rockler 60th Ann. Shark
Location: Dallas, TX USA
Contact:

Re: Hall of Lines

Post by nicksilva »

scottp55 wrote:....I'd just have pick a groove and trust Nick not to take me to a waterfall or a Rabbit Hole......
scott
what do you think is around the corner? :D
"Out of my mind. Back in 5 Minutes."

User avatar
scottp55
Vectric Wizard
Posts: 3818
Joined: Thu May 09, 2013 11:30 am
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10
Location: Kennebunkport, Maine, US

Re: Hall of Lines

Post by scottp55 »

Reminded me of a wildwater race in Massachusetts Nick:)
Scoped out the river the day before, and picked out our lines.....THEN the day of the race they opened 3 more sluices on the dam above :shock:
Another 4 feet of water, and wasn't a problem for most of the wildwater, BUT there was a GORGE with what WAS a 5 foot drop and only one real way to go over, that lead you directly to the only path through the Class4 "Rock Garden" below.
NOW it was 8-10 foot drop with a WHIRLPOOL in the center, and 60 foot wide selection of ledge choices, and "Rock Garden" now had 10 ways in, BUT only ONE led you to the main river stream :D

Three wetsuited dive teams at the drop that were kept busy, and paddlers from cross country were madly scrambling and carrying their boats over the Garden when the paths they were washed into petered out to boulders :D :D

Probably a 100 foot waterfall Nick!!!! :) :)
"Flatness is King"
Brady W.

scott

nicksilva
Vectric Craftsman
Posts: 295
Joined: Thu Aug 21, 2014 8:13 pm
Model of CNC Machine: ULS M300, Rockler 60th Ann. Shark
Location: Dallas, TX USA
Contact:

Re: Hall of Lines

Post by nicksilva »

scottp55 wrote:Reminded me of a wildwater race in Massachusetts Nick:)
Probably a 100 foot waterfall Nick!!!! :) :)
DANG! And I have trouble jumping into the deep end of the pool.
"Out of my mind. Back in 5 Minutes."

User avatar
scottp55
Vectric Wizard
Posts: 3818
Joined: Thu May 09, 2013 11:30 am
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10
Location: Kennebunkport, Maine, US

Re: Hall of Lines

Post by scottp55 »

:)
"Flatness is King"
Brady W.

scott

User avatar
Creation in Wood
Vectric Wizard
Posts: 525
Joined: Thu May 28, 2015 8:58 pm
Model of CNC Machine: Legacy Maverick ATC 4x8 CNC
Location: Monument, Colorado USA

Re: Hall of Lines

Post by Creation in Wood »

Thank you
Thank You
Doug

Post Reply