Grape Man 3 inch

This is the place to post images of work produced using Aspire
Post Reply
mark-s
Vectric Apprentice
Posts: 213
Joined: Sat Feb 03, 2018 2:03 am
Model of CNC Machine: diy 4 X 4 CNC Router
Location: So. Cal.

Grape Man 3 inch

Post by mark-s »

Here is my grape man.
3 inch
maple, clear matte finish.
Scottp55 got me hooked on miniatures .
And I love it.
Not sorry...LOL.
mark-s
CNC GRAPE MAN 5.jpg

User avatar
mtylerfl
Vectric Wizard
Posts: 4904
Joined: Thu Jan 29, 2009 3:54 am
Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
Location: Brunswick, GA
Contact:

Re: Grape Man 3 inch

Post by mtylerfl »

Dang! That looks wonderful, Mark!

Scott is starting to pique my interest in the tiny things too! I’ve had a particular personal project in mind for years that will require “teeny” detailed carvings.

If I can ever make the time for my “secret project”, Scott will be my go-to guy for teeny tips and advice!
Michael Tyler

carvebuddy.com

facebook.com/carvebuddy

-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC

User avatar
TReischl
Vectric Wizard
Posts: 3728
Joined: Thu Jan 18, 2007 6:04 pm
Model of CNC Machine: 8020 Build 48X36X10 RP 2010 Screenset
Location: Leland NC

Re: Grape Man 3 inch

Post by TReischl »

Nicely done Mark!

Yup doing small stuff has lots of positives.

Less expensive.
Less time.
Can carry in pocket and show everyone you meet. (instead of showing pics on a phone)

One drawback. . . . My small stuff winds up getting given away. I am a moosh.
"If you see a good fight, get in it." Dr. Vernon Jones

User avatar
scottp55
Vectric Wizard
Posts: 3826
Joined: Thu May 09, 2013 11:30 am
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10
Location: Kennebunkport, Maine, US

Re: Grape Man 3 inch

Post by scottp55 »

And I in turn blame my Dad for getting addicted Mark :)

We were making buttons at the time, and Dad and I used to "Play" during his visits from St. Albans, Vermont.
One day in April 2015 he said "Can we make a 3D button?" and I say "I Dunno"
All I had was .0625"Onsrud TBN($76!!), so I lied like heck to my machine in Cut3D about an Onsrud 30degree engraving with a .01" flat I'd been gifted calling it an imaginary TBN....
And we played with Todd Bailey's free 4M3D Celtic, and a Loon Scene on some Walnut I already had taped down all day.
DAD PLAYING BUTTON 3D FIRST DAY 4.24.15.jpg
AND at the Button Show the next day...the 3D's (after sanding all night and finishing) were the biggest hit!
President of Maine Button Society, later asked for a dozen Bloodwood "Loon" buttons to take to the annual National Show, where she sold out in 3 hours to collectors for $40 a pop!! :D
12.5.2015 LOON loon 1.jpg
As Dad dropped me off, he said "How small can you go" AGAIN "I Dunno"....and I was off :)
5.10.2015 PUTZ ORIGINAL 2C CLIMB.jpg
Thank goodness for VCP8.5 upgrade!!!!
I could finally get an accurate preview :)

Anytime Michael...LOVE "Secret Projects" :D

Mark, Ted is right...carrying them around in a shirt pocket, AND dropping signed "Samples" of at relevant shops with a business card to the Owner works WAY better than sending pics!
As you know, playing with a piece that fits your hand is better than a 100 brochures shipped out:)
IF you can find one of the Owner's favorite subjects...all the better!
Having a wide representation of your pieces wrapped in a NICE fabric/chamois/fleece/etc. in the car if there's interest is a good idea. AND have your costs figured out HIGH!
High end niche markets will probably be your market, as well as word of mouth.

Ted is right!
When you see a person's eyes Light Up as they fall in love with a piece, very hard not to give it to them.
BUT, THEY will show it off to everybody they know, and word of mouth can surprise you!!

Rambling again:(
NICE One Mark!!
scott
"Flatness is King"
Brady W.

scott

LittleGreyMan
Vectric Apprentice
Posts: 918
Joined: Fri May 15, 2015 1:10 pm
Model of CNC Machine: 3 axis small size machine
Location: France

Re: Grape Man 3 inch

Post by LittleGreyMan »

Bad news, Scott: you'll have now to share the Scott touch with Mark (:

Nice job

User avatar
scottp55
Vectric Wizard
Posts: 3826
Joined: Thu May 09, 2013 11:30 am
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10
Location: Kennebunkport, Maine, US

Re: Grape Man 3 inch

Post by scottp55 »

Nah Didier:)
Mark is doing just fine by himself! :)
Besides, I can always quadruple(or more my cut times with smaller bits and limit myself to files with super fine details and go TINY:)
Maybe include a 10X loupe so people can see the difference? :D
scott
"Flatness is King"
Brady W.

scott

Post Reply