EZ Prism Star modeling
- highpockets
- Vectric Wizard
- Posts: 3667
- Joined: Tue Jan 06, 2015 4:04 pm
- Model of CNC Machine: PDJ Pilot Pro
Re: EZ Prism Star modeling
Michael your videos are great and always informative. Thanks...
John
Maker of Chips
Maker of Chips
- rtibbs
- Vectric Wizard
- Posts: 411
- Joined: Mon Nov 12, 2018 11:15 pm
- Model of CNC Machine: Shopbot desktop
- Location: Central Florida
Re: EZ Prism Star modeling
Whipped that out before church. Would have taken me until next Sunday to do that
Thanks for the great video Michael. It’s now bookmarked for future use
Ron
Thanks for the great video Michael. It’s now bookmarked for future use
Ron
- mtylerfl
- Vectric Archimage
- Posts: 5896
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: EZ Prism Star modeling
Well, thank you all! I’m happy to hear it is helpful!
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
-
- Vectric Wizard
- Posts: 411
- Joined: Thu Apr 06, 2017 3:07 am
- Model of CNC Machine: Camaster Stinger SR24
- Location: Addison, PA
Re: EZ Prism Star modeling
For a “totally off the cuff and unscripted” video that was a most most excellent tutorial!
Thank you for the education.
Thank you for the education.
Joe
I have a chip on my shoulder....several more in my hair and lots more all over my shop floor.
I have a chip on my shoulder....several more in my hair and lots more all over my shop floor.
- mtylerfl
- Vectric Archimage
- Posts: 5896
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: EZ Prism Star modeling
Thank you! I was going to just draw all the vectors before leaving the house so I would have everything ready to go after lunch. But, I couldn’t resist and just went ahead and did the video in one take right then and there! (I wanted to keep it around 5 or 6-minutes, but ran a couple minutes longer since I didn’t do a practice run.)
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
- mfirlott
- Vectric Craftsman
- Posts: 299
- Joined: Thu Feb 07, 2013 12:49 am
- Model of CNC Machine: Stinger 1 (2014)
- Location: Cantley, Quebec, Canada
- Contact:
Re: EZ Prism Star modeling
Wow Michael...that really helps. Thanks so much for pumping this out...especially before church
It was VERY helpful and it's bookmarked. I will play with 2-rail sweeps more now that I have a better understanding. I'm sure it'll help me develop some of my own models (which haven't gone so well in the past )
THANKS AGAIN Michael!!!
It was VERY helpful and it's bookmarked. I will play with 2-rail sweeps more now that I have a better understanding. I'm sure it'll help me develop some of my own models (which haven't gone so well in the past )
THANKS AGAIN Michael!!!
(Mitch)
CAMaster Stinger I
Vectric Aspire
Epilog 45watt Helix Laser
CAMaster Stinger I
Vectric Aspire
Epilog 45watt Helix Laser
- mtylerfl
- Vectric Archimage
- Posts: 5896
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: EZ Prism Star modeling
You are very Welcome!
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
Re: EZ Prism Star modeling
thanks , turned out good
Re: EZ Prism Star modeling
Excellent tutorial. Thanks,
Phil
Phil