Just recently, I had an issue with my computer, which warranted a formatting. In the aftermath of that, I encountered a problem with my reinstallation of Aspire. Now, I cannot honestly say that the problem resides with the installation, in and of itself, but there IS a hurdle that I can't seem to jump. Following, is what I am faced with:
In my first project design, after the new install, I set up a 90° V bit for carving, and a 1/8" EM for clearing. Then, I thought that I might fare better using a 60° V bit, instead. I found that I was not permitted to make that change, as the choice selection was greyed out. For the sake of it, I also tried changing the set 1/8"EM to a 1/4"EM, and the same situation occurred.
What could have gone wrong?
Can't change tools.
Can't change tools.
Blessings,
Nathan
Vectric Aspire 11
Axiom Iconic 8
Onefinity X50
Jtech 2.8w & 7w lasers
Nathan
Vectric Aspire 11
Axiom Iconic 8
Onefinity X50
Jtech 2.8w & 7w lasers
- adze_cnc
- Vectric Wizard
- Posts: 4373
- Joined: Sat Jul 27, 2013 10:08 pm
- Model of CNC Machine: AXYZ 4008
- Location: Vancouver, BC, Canada
Re: Can't change tools.
Does you tool selection look something like this:
If so, your tool hasn't been set up yet.
If so, your tool hasn't been set up yet.
Re: Can't change tools.
Hey Adze,
Yes, it does look like that. But you know what? Just before visiting back here, I (being one to not easily give up) had given another shot at it. And - lo and behold - The software had changed its mind, and acted right . I did absolutely nothing different, but I am back in stroke again. I thank you, though, for responding.
Yes, it does look like that. But you know what? Just before visiting back here, I (being one to not easily give up) had given another shot at it. And - lo and behold - The software had changed its mind, and acted right . I did absolutely nothing different, but I am back in stroke again. I thank you, though, for responding.
Blessings,
Nathan
Vectric Aspire 11
Axiom Iconic 8
Onefinity X50
Jtech 2.8w & 7w lasers
Nathan
Vectric Aspire 11
Axiom Iconic 8
Onefinity X50
Jtech 2.8w & 7w lasers
- adze_cnc
- Vectric Wizard
- Posts: 4373
- Joined: Sat Jul 27, 2013 10:08 pm
- Model of CNC Machine: AXYZ 4008
- Location: Vancouver, BC, Canada
Re: Can't change tools.
Perhaps the second time (the working time) the material at the top was different with that material the bit was defined.
Re: Can't change tools.
I can understand what you're getting at, but I was (actually) attempting it again with the same material (3/16' whiteboard), and settings. But I thank you, for the suggestion.
Blessings,
Nathan
Vectric Aspire 11
Axiom Iconic 8
Onefinity X50
Jtech 2.8w & 7w lasers
Nathan
Vectric Aspire 11
Axiom Iconic 8
Onefinity X50
Jtech 2.8w & 7w lasers
- martin54
- Vectric Archimage
- Posts: 7349
- Joined: Fri Nov 09, 2012 2:12 pm
- Model of CNC Machine: Gerber 48, Triac PC, Isel fixed gantry
- Location: Kirkcaldy, Scotland
Re: Can't change tools.
Are you sure you didn't select a tool that didn't have it's parameters already set? The only time I have ever seen the screenshot adze_cnc posted was when I was using a material that some tools weren't defined on. For example I have several different 60 degree V bits but don't have them all defined for every material that I use. If I select a different material I tend to fill in the details for each tool as & when I need to use it rather than spend hours editing tools that I may never use for a particular material