Aspire camp at Mcgrews 2020 updates

This forum is for general discussion about Aspire
Post Reply
James McGrew
Vectric Apprentice
Posts: 12
Joined: Thu Jan 31, 2019 11:18 am
Model of CNC Machine: CAMaster ATC 508 Cobra

Aspire camp at Mcgrews 2020 updates

Post by James McGrew »

Camp seats are filling well, the correct registration form is attached to this post.

NOTE: A registration form must be sent and payment made to hold a seat.

this is the previous thread

https://forum.vectric.com/viewtopic.php?f=27&t=33486
Attachments
aspire registration 2020 ver ab.pdf
ASPIRE CAMP REGISTRATION
(108.11 KiB) Downloaded 58 times

James McGrew
Vectric Apprentice
Posts: 12
Joined: Thu Jan 31, 2019 11:18 am
Model of CNC Machine: CAMaster ATC 508 Cobra

Re: ASPIRE CAMP AT MCGREWS 2020 UPDATES

Post by James McGrew »

INFORMATION CAN BE FOUND ON SEVERAL MACHINE FORUMS AND FACEBOOK

https://www.facebook.com/aspirecampsforthevecheads/

James McGrew
Vectric Apprentice
Posts: 12
Joined: Thu Jan 31, 2019 11:18 am
Model of CNC Machine: CAMaster ATC 508 Cobra

Re: Aspire camp at Mcgrews 2020 updates

Post by James McGrew »

AGENDA AGENDA !!

Here is first draft,,

subject to small changes but all the speakers are in tune !!

Camp is over 1/2 full and it is still pretty early We will have to cut off seats as we cannot hold more than 100-125 with speakers and support persons comfortably, this is held in a cabinet shop not a hotel ballroom !

James McGrew
Vectric Apprentice
Posts: 12
Joined: Thu Jan 31, 2019 11:18 am
Model of CNC Machine: CAMaster ATC 508 Cobra

Re: Aspire camp at Mcgrews 2020 updates

Post by James McGrew »

Agenda Agenda,, So many asked about being new to Vectric and CNC, Whether or not this will benefit them,, the Answer for me is I never had anyone in ten years tell me it did not benefit them, yet all say it was good if not great for them.

Here is the edited Agenda we do have seats and more have sold when compared to 2018 at this time, hopefully all who want to attend will register !!
Attachments
2020 Aspire Camp Agenda 2020.pdf
(115.91 KiB) Downloaded 37 times
2020 Aspire Camp Agenda 2020_Page_1.jpg
2020 Aspire Camp Agenda 2020_Page_2.jpg
2020 Aspire Camp Agenda 2020_Page_3.jpg
aspire registration 2020 ver ab.pdf
(111.96 KiB) Downloaded 17 times

James McGrew
Vectric Apprentice
Posts: 12
Joined: Thu Jan 31, 2019 11:18 am
Model of CNC Machine: CAMaster ATC 508 Cobra

Re: Aspire camp at Mcgrews 2020 updates

Post by James McGrew »

Getting calls and Emails about seat availability,, We still have seats available Yet we are over 60 seats so far,, Look forward to seeing all Who are new and returning. This may be the last Camp i am going to hold for a while as we will be seeking to move the shop next year. So I hope we all pull out the Stops for the Best one yet !!

Feel free to call or email with any questions thanks

James McGrew
Vectric Apprentice
Posts: 12
Joined: Thu Jan 31, 2019 11:18 am
Model of CNC Machine: CAMaster ATC 508 Cobra

Re: Aspire camp at Mcgrews 2020 updates

Post by James McGrew »

Camp will be resceduled, most everyone has aked to do this, I have only had two cancellations
Attachments
Capture.JPG

Post Reply