Vectric Cribbage Board Project

This forum is for general discussion regarding VCarve Pro
Post Reply
mikenbrenda
Posts: 28
Joined: Thu Nov 22, 2018 6:46 pm
Model of CNC Machine: Shapeoko 3 XXL

Vectric Cribbage Board Project

Post by mikenbrenda »

I wanted to make this free project and I can’t find .233 end mills and .39 ball nose bits, is there an alternative? I found the .115 end mill, I wanted to buy on Amazon so I get them quick why not just use standard sizes? Like .25? Why not use standard size so is newbies can get into it easy.. Lol maybe I’m being stupid somewhere

4DThinker
Vectric Wizard
Posts: 1308
Joined: Sun Sep 23, 2012 12:14 pm
Model of CNC Machine: CNC Shark Pro

Re: Vectric Cribbage Board Project

Post by 4DThinker »

Looks like whoever made the original file was using metric bits. .233 is very close to 6mm, and .39 is very close to 10mm. The .115 was likely a 3mm bit.

The critical decision about what size bits you could use instead is based on what each bit is expected to do. If the .233 bit was just doing profile cuts around the perimeter then a .25" bit should be fine. If the .115" bit was drilling/pocketing holes then you could use a .125" bit if the hole diameter was .125 or larger. Not sure what the ball end bit was used for, but a 3/8 (.375") bit would likely be a fine alternative.

4D

User avatar
TReischl
Vectric Wizard
Posts: 3159
Joined: Thu Jan 18, 2007 6:04 pm
Model of CNC Machine: 8020 Build 48X36X10 RP 2010 Screenset
Location: Leland NC

Re: Vectric Cribbage Board Project

Post by TReischl »

Well it sorta looks like someone did not know that 25.4 is a magic number. . . .

The peg holes are drawn at .125 so that should solve that problem.

I don't see where any of the rest of it is critical either.

Like Mr 4D said, imperial tools will work fine.
"If you see a good fight, get in it." Dr. Vernon Jones

User avatar
rscrawford
Vectric Wizard
Posts: 967
Joined: Mon Jan 17, 2011 6:49 pm
Model of CNC Machine: CAMaster Cobra 408 ATC, ShopSabre IS408
Location: Wetaskiwin, Alberta
Contact:

Re: Vectric Cribbage Board Project

Post by rscrawford »

One must remember that all of the world (except one country) uses metric. . .

And Vectric headquarters are not in the US. . .
Russell Crawford
http://www.cherryleaf-rustle.com

tomgardiner
Vectric Wizard
Posts: 382
Joined: Thu Oct 02, 2014 1:49 pm
Model of CNC Machine: FMT Patriot 4 x8

Re: Vectric Cribbage Board Project

Post by tomgardiner »

You are forgetting that Burma/myanmar and Liberia use the imperial system.

User avatar
adze_cnc
Vectric Apprentice
Posts: 813
Joined: Sat Jul 27, 2013 10:08 pm
Model of CNC Machine: AXYZ 4008
Location: Vancouver, BC, Canada

Re: Vectric Cribbage Board Project

Post by adze_cnc »

I keep getting people saying things like:
  • what’s half of 1 and 3/16 inches (yuk, yuk, yuk) — easy 1/2” plus 3/32”…next...
  • problem with using inches is you need to use fractions rather than decimals — huh?!?
I get my own back by saying: I’m 1880 mm tall; how many decimeters is that? And lo and behold these people seem incapable of providing the answer.

I use “Imperial” / “Metric” depending on what is necessary and there are no pros or cons to sway me one way or another. Nor do I feel the need to enter a 1/4” bit into the database as 6.35mm—let the software do the conversion for you.

Although I must say that the Babylonians had it right: base tweleve is superior to base ten (more factors: 1, 2, 3, 4, 6, 12 rather than 1, 2, 5, 10)….

Post Reply