For some reason I am having a hard time getting a post for my machine. Can any one give me direction?
Machine is a 2017 Selexx Fanuc controller 4 x 8 (right to left) Inches
Can someone send me one?
Thanks, Josh
Selexx Post Processor
-
- Posts: 8
- Joined: Thu Apr 04, 2019 11:23 pm
- Model of CNC Machine: Selexx 4x8 fanuc (right to left)
- Rcnewcomb
- Vectric Archimage
- Posts: 5887
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: Selexx Post Processor
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
- dealguy11
- Vectric Wizard
- Posts: 2464
- Joined: Tue Sep 22, 2009 9:52 pm
- Model of CNC Machine: Anderson Selexx 510
- Location: Henryville, PA
Re: Selexx Post Processor
I used the "Omnitech_inch_arc" postprocessor, but I had to make a few changes to it. Omnitech is what Anderson used to call the Selexx line. The default version of this postprocessor is set up to use the "ij" format for G2 and G3 arc commands, rather than the "r" version. The ij version specifies the center of the arc and the r version specifies the radius. The ij version didn't work on my machine, so I changed it to the r version. I can't guarantee this will work with your machine, but it works fine on my 2017 Selexx 510 with a Fanuc controller. Here's my edited post-processor. Your results may vary.
- Attachments
-
- Omnitech_inch_arc SG.zip
- (1.09 KiB) Downloaded 148 times
Steve Godding
Not all who wander (or wonder) are lost
Not all who wander (or wonder) are lost
-
- Posts: 8
- Joined: Thu Apr 04, 2019 11:23 pm
- Model of CNC Machine: Selexx 4x8 fanuc (right to left)
Re: Selexx Post Processor
Thank you so much! Would this work even if i custom ordered mt machine right to left, so the th 0,0 is in the back right corner? "Y" is short , "X" is long axis. Do I need to change my table size on this post?
- dealguy11
- Vectric Wizard
- Posts: 2464
- Joined: Tue Sep 22, 2009 9:52 pm
- Model of CNC Machine: Anderson Selexx 510
- Location: Henryville, PA
Re: Selexx Post Processor
Pretty sure there is no table size in the post, and I don't see why it wouldn't work with your table configuration. Give it a try. You'll know pretty quickly if it will work, and if it doesn't you'll just get a limit error and the machine will stop.
Steve Godding
Not all who wander (or wonder) are lost
Not all who wander (or wonder) are lost
- dealguy11
- Vectric Wizard
- Posts: 2464
- Joined: Tue Sep 22, 2009 9:52 pm
- Model of CNC Machine: Anderson Selexx 510
- Location: Henryville, PA
Re: Selexx Post Processor
Just one more thing. If your xy origin is at the back right (mine is at the back left), then I think when you design your projects you'll need to make sure you're designing to the left of Y. In VCarve Pro, I think you need to set your XY Datum point to the bottom right position (because when you stand on that side of the machine with x0y0 at your right, x to the left and y going away from you, that's how the point will sit relative to the xy axis). If you have already know this, then just ignore me.
Steve Godding
Not all who wander (or wonder) are lost
Not all who wander (or wonder) are lost
-
- Posts: 8
- Joined: Thu Apr 04, 2019 11:23 pm
- Model of CNC Machine: Selexx 4x8 fanuc (right to left)
Re: Selexx Post Processor
Thank, but didn't work. The machine just stuck in the 0,0 corner and barely moved. I email Vectric.
-
- Posts: 8
- Joined: Thu Apr 04, 2019 11:23 pm
- Model of CNC Machine: Selexx 4x8 fanuc (right to left)
Re: Selexx Post Processor
I try and drop my Vcarve post into Photo Carve exec. file Post and I get this error code. Can you help?
- Adrian
- Vectric Archimage
- Posts: 14544
- Joined: Thu Nov 23, 2006 2:19 pm
- Model of CNC Machine: ShopBot PRS Alpha 96x48
- Location: Surrey, UK
Re: Selexx Post Processor
PhotoVCarve is a much older program so many of the sections in a modern VCarve post processor it knows nothing about hence the errors. You would need to remove the sections it's not happy about. PhotoVCarve doesn't support ARC commands or tool changing for example.Benton Contruction wrote:I try and drop my Vcarve post into Photo Carve exec. file Post and I get this error code. Can you help?