Cutting text
-
- Posts: 24
- Joined: Sat Aug 22, 2015 1:41 am
- Model of CNC Machine: 141001
- Location: Chula, MO
Cutting text
I'm having a problem with writing text. The bit will drag across my project from letter to letter. it comes up but not all of the way out of the letter. I believe that I have adjusted the distance above the project correctly but it sill drags. I need some help in trying to fix this problem.
- FixitMike
- Vectric Wizard
- Posts: 2177
- Joined: Sun Apr 17, 2011 5:21 am
- Model of CNC Machine: Shark Pro Plus (retired)
- Location: Burien, WA USA
Re: Cutting text
One possibility is that the Z axis is loosing steps when it is attempting to rise. The most common cause is hitting a hard upper limit.
Good judgement comes from experience.
Experience comes from bad judgement.
Experience comes from bad judgement.
- Rcnewcomb
- Vectric Archimage
- Posts: 5927
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: Cutting text
Does the issue show up in the preview?
Can you post an example file that shows the problem?
(How do I upload files or photos to the forum?)
If the file is too large to upload here you can use a file sharing site such as drive.google.com, onedrive.com, or dropbox.com. They all have free accounts available
Can you post an example file that shows the problem?
(How do I upload files or photos to the forum?)
If the file is too large to upload here you can use a file sharing site such as drive.google.com, onedrive.com, or dropbox.com. They all have free accounts available
- Upload the file to the file sharing site
- Make the link shareable
- Share the link to the file here
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
-
- Posts: 24
- Joined: Sat Aug 22, 2015 1:41 am
- Model of CNC Machine: 141001
- Location: Chula, MO
Re: Cutting text
The file isn't very large and the dragging of the bit happens at the beginning of the file. I can't speak to the Z axis because I believe that I have all of the parameters set properly. Is there a way to correct this issue. Thinking I can run the router down all the way to the bed until it bottoms out. I haven't tried this yet just waiting it hear from any one who can speak to this problem.
- Rcnewcomb
- Vectric Archimage
- Posts: 5927
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: Cutting text
It would really help to see the .CRV file.just waiting it hear from any one who can speak to this problem
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
-
- Posts: 24
- Joined: Sat Aug 22, 2015 1:41 am
- Model of CNC Machine: 141001
- Location: Chula, MO
Re: Cutting text
I will return later. I don't know how to share files yet, I'll have to ask my granddaughter to see if she can teach me.
- Adrian
- Vectric Archimage
- Posts: 14680
- Joined: Thu Nov 23, 2006 2:19 pm
- Model of CNC Machine: ShopBot PRS Alpha 96x48
- Location: Surrey, UK
Re: Cutting text
You have two options in Cut2D (and with VCarve/Aspire) for z-zero position. The z-zero can be on top of the material or the bottom (the top of the spoil board/table). You can use whichever you prefer but when you set the z-zero on the actual machine using your control software it MUST be the same as you've set it in Cut2D.Gunny Rogers wrote: ↑Tue Apr 20, 2021 12:41 amThinking I can run the router down all the way to the bed until it bottoms out. I haven't tried this yet just waiting it hear from any one who can speak to this problem.
The Z clearance parameters within Cut2D on the Material Setup dialog won't allow you to set values that would cause the bit to drag across the material so if you're seeing that it's something wrong with the way you're setting the z-zero, the material thickness doesn't match what you've set in the job (if you're zeroing on the table surface) or the material isn't flat.
-
- Posts: 24
- Joined: Sat Aug 22, 2015 1:41 am
- Model of CNC Machine: 141001
- Location: Chula, MO
Re: Cutting text
I will try to get it right when I am setting the z-zero and placing the machine no the bed to see if that corrects the bit from being dragged across the project. Thank you