Search found 485 matches
- Sat May 08, 2021 2:18 pm
- Forum: VCarve - General
- Topic: How to add my logo to the job setup sheet
- Replies: 5
- Views: 1534
Re: How to add my logo to the job setup sheet
Thanks You Jeff
- Sat May 08, 2021 1:08 pm
- Forum: VCarve - General
- Topic: How to add my logo to the job setup sheet
- Replies: 5
- Views: 1534
How to add my logo to the job setup sheet
I would like to add my logo to my job set up sheets in place of the vectric log
Is there a way to do that.
Thanks Jeff
Is there a way to do that.
Thanks Jeff
- Thu Mar 18, 2021 4:37 pm
- Forum: VCarve - General
- Topic: My First 2 sided job.
- Replies: 2
- Views: 835
My First 2 sided job.
Attached is a file of a 2 sided job that is a left and right side of a cabinet being cutout of 1 piece of wood.I was wondering If some one wood look at the vile and see if I did right
And if not make any suggestion please.
Thanks Jeff
And if not make any suggestion please.
Thanks Jeff
- Fri Feb 26, 2021 9:32 pm
- Forum: VCarve - General
- Topic: MDF Shaker Style 1 piece cabinet doors
- Replies: 14
- Views: 4629
Re: MDF Shaker Style 1 piece cabinet doors
Thanks for the reply there is a ATC processor for my Shapeoko I found so now I need to install it. And my controler will then pause and will stop for a tool change then it will go to what is called a bit setter to reset the z height for that bit then run the toolpath for that bit.
Thanks Jeff
Thanks Jeff
- Fri Feb 26, 2021 5:07 pm
- Forum: VCarve - General
- Topic: MDF Shaker Style 1 piece cabinet doors
- Replies: 14
- Views: 4629
Re: MDF Shaker Style 1 piece cabinet doors
one last question .when saving the toolpaths created for the pocket with 3 different bits do I out put them to 1 toolpath or so I do them separately
I do not have a tool changer.
Jeff
I do not have a tool changer.
Jeff
- Thu Feb 25, 2021 2:42 pm
- Forum: VCarve - General
- Topic: MDF Shaker Style 1 piece cabinet doors
- Replies: 14
- Views: 4629
Re: MDF Shaker Style 1 piece cabinet doors
Steve I checked the feed rates and with my Shapeoko with a DEWALT 611 router which limits me to 1/4' and 1/8" shank bits
Which I believe were not supposed run at 400 inches ipm So I will need to do some adjusting .
Thanks Jeff
Which I believe were not supposed run at 400 inches ipm So I will need to do some adjusting .
Thanks Jeff
- Thu Feb 25, 2021 2:24 pm
- Forum: VCarve - General
- Topic: MDF Shaker Style 1 piece cabinet doors
- Replies: 14
- Views: 4629
Re: MDF Shaker Style 1 piece cabinet doors
Thanks for posting the v carve file I is just what I I wanted
I always get great help here.
Jeff
I always get great help here.
Jeff
- Thu Feb 25, 2021 1:53 pm
- Forum: VCarve - General
- Topic: MDF Shaker Style 1 piece cabinet doors
- Replies: 14
- Views: 4629
Re: MDF Shaker Style 1 piece cabinet doors
Steve i can not open the file to change the check the feeds and or make changes
I thought you would send my a vectric design file
Jeff
I thought you would send my a vectric design file
Jeff
- Thu Feb 25, 2021 1:04 pm
- Forum: VCarve - General
- Topic: MDF Shaker Style 1 piece cabinet doors
- Replies: 14
- Views: 4629
Re: MDF Shaker Style 1 piece cabinet doors
Steve Thank you very much for doing this. I really appreciate
Jeff
Jeff
- Wed Feb 24, 2021 4:45 pm
- Forum: VCarve - General
- Topic: MDF Shaker Style 1 piece cabinet doors
- Replies: 14
- Views: 4629
Re: MDF Shaker Style 1 piece cabinet doors
Steve, Thanks for the reply, Would you be willing to take my door file and and set up the toolpaths that you would use My largest pocketing is only 1 "in dia but I have all the other bits sizes you recommend.
This is going to be my first attempt at doing something like this.
thanks Jeff
This is going to be my first attempt at doing something like this.
thanks Jeff
- Tue Feb 23, 2021 12:21 pm
- Forum: VCarve - General
- Topic: MDF Shaker Style 1 piece cabinet doors
- Replies: 14
- Views: 4629
MDF Shaker Style 1 piece cabinet doors
I have want to make a shaker style 1 piece Kitchen cabinet door. I have attached a file that I did to create the the door. The inside edge of each of the door tops sides and bottom have a bevel on them Could you take a look at my file and see if I have created it properly and that I am going to have...
- Tue Feb 16, 2021 1:25 pm
- Forum: VCarve - General
- Topic: Question About Tiling
- Replies: 3
- Views: 827
Re: Question About Tiling
Thanks. where do i find the old post you are referring to
Jeff
Jeff
- Mon Feb 15, 2021 4:32 pm
- Forum: VCarve - General
- Topic: Question About Tiling
- Replies: 3
- Views: 827
Question About Tiling
In the Tiling tool do the tiles all have to be the same spacing. So another words could you have the T1 tile be 25" T2 be 30"
T3 be 18"
Thanks Jeff
T3 be 18"
Thanks Jeff
- Fri Jan 29, 2021 9:25 pm
- Forum: VCarve - General
- Topic: Downloading Dado gadget
- Replies: 4
- Views: 1140
Re: Downloading Dado gadget
That link took me to the same one I downloaded
version1.1 the oicture is of a Error Message I get when I try to run it
The other thing is that I don't get ai install file
Jeff
version1.1 the oicture is of a Error Message I get when I try to run it
The other thing is that I don't get ai install file
Jeff
- Fri Jan 29, 2021 2:42 pm
- Forum: VCarve - General
- Topic: Downloading Dado gadget
- Replies: 4
- Views: 1140
Downloading Dado gadget
I tried to download the dado gadget . It did not run in vcarve pro 10.5
Do I need to download the installer file from Vectric site first to get them installed
Want to install the Dado gadget version 1.1
Jeff
Do I need to download the installer file from Vectric site first to get them installed
Want to install the Dado gadget version 1.1
Jeff