Search found 667 matches
- Wed May 10, 2017 6:39 pm
- Forum: Aspire - General
- Topic: file transfer
- Replies: 8
- Views: 3976
Re: file transfer
there is always a screen shot taken from different angles
- Sat Apr 29, 2017 6:34 pm
- Forum: VCarve - General
- Topic: Tear out..
- Replies: 10
- Views: 5171
Re: Tear out..
I do mostly black walnut and cherry. each project had its share of fuzzies. About 8 months ago i started cutting against the grain and fuzzies are a thing of the past. My go to bit right now is Amana 1/16 ball nose which is a 4 flute. https://www.amazon.com/gp/product/B01AA4M7BA/ref=oh_aui_detailpag...
- Thu Apr 27, 2017 7:58 pm
- Forum: VCarve - General
- Topic: Finding the exact center
- Replies: 15
- Views: 7869
Re: Finding the exact center
and i never work from the corner, but it all works. It is just a matter of what you get use to.
- Thu Apr 27, 2017 1:48 pm
- Forum: VCarve - Tips and Tricks
- Topic: Finishing Pass when V-Carving
- Replies: 3
- Views: 3072
Re: Finishing Pass when V-Carving
How i do finishing passes but not sure it relates to your question. But for each v-bit i have 2 tool paths. One does the initial carving. The other has a pass depth set as deep as the bit can go, but remember it is restricted by the vector. Then i set a start dept at a tiny fraction above where the ...
- Thu Apr 27, 2017 12:20 pm
- Forum: VCarve - General
- Topic: Finding the exact center
- Replies: 15
- Views: 7869
Re: Finding the exact center
The bits are fine but i use a laser.
- Sat Apr 01, 2017 3:03 pm
- Forum: VCarve - General
- Topic: Wide Boards - where to get!
- Replies: 15
- Views: 9304
Re: Wide Boards - where to get!
Yeah what Leo said.
- Mon Mar 20, 2017 1:57 am
- Forum: VCarve - General
- Topic: Making a spoilboard using vcarve
- Replies: 18
- Views: 10556
Re: Making a spoilboard using vcarve
i was just referring to you chewing up spoil boards. i have my own history there.
- Mon Mar 20, 2017 1:51 am
- Forum: VCarve - General
- Topic: Large Wood Live Edge Slab
- Replies: 7
- Views: 3645
Re: Large Wood Live Edge Slab
I have been up against the same type thing before and just eyeballed it. But whats wrong with importing a picture of your slab and size it in vectric. That should give you something to look at. Just a thought.
- Mon Mar 20, 2017 1:25 am
- Forum: VCarve - General
- Topic: Making a spoilboard using vcarve
- Replies: 18
- Views: 10556
Re: Making a spoilboard using vcarve
What i do, and i am sure some will shake their heads, and it works. I add 1/4 inch rubber washers under my work piece and then clamp it down. Knowing the thickness of the work piece i cut all the way though it with out touching the spoil board.
- Mon Mar 13, 2017 4:52 pm
- Forum: Aspire - Gallery
- Topic: Maltese Cross Clock
- Replies: 7
- Views: 6362
Re: Maltese Cross Clock
I like it pretty cool.
- Fri Feb 24, 2017 1:28 am
- Forum: Aspire - General
- Topic: Ever have a project that was cursed?
- Replies: 15
- Views: 6663
Re: Ever have a project that was cursed?
You are starting to remind me of some one and that one being me. Not sure about your machine but shopbot has this. Its their c3 command, which is a constant location on the table. I always work from the center of my work piece. So before doing any cutting, i mark the center of the piece. Then do the...
- Thu Feb 23, 2017 9:39 pm
- Forum: Aspire - Gallery
- Topic: WaltS your not alone
- Replies: 13
- Views: 8131
Re: WaltS your not alone
From now on i will clamp them evenly, but before then i was not paying attention.
- Thu Feb 23, 2017 7:35 pm
- Forum: Aspire - Gallery
- Topic: WaltS your not alone
- Replies: 13
- Views: 8131
Re: WaltS your not alone
I am always tightening my clamps during different toolpaths, which may have caused a problem in one of my carving. It was a 3-d plaque surrounded by v-carving on a flat area. i noticed that the v-carving was deeper on one side than the other. My guess is that this was caused by tightening one side m...
- Sun Feb 19, 2017 3:52 pm
- Forum: VCarve - General
- Topic: Clipart a bit off
- Replies: 20
- Views: 8462
Re: Clipart a bit off
Its been so long since i have used partworks that i am not sure i could tell you the right procedure. I have aspire 8.5.
- Sun Feb 19, 2017 2:27 pm
- Forum: VCarve - General
- Topic: Clipart a bit off
- Replies: 20
- Views: 8462
Re: Clipart a bit off
What software are you using and which model of the ape are you using "A or B"
I am goint to send you a pm.
I am goint to send you a pm.