Search found 35 matches
- Sun Feb 18, 2018 6:45 pm
- Forum: Aspire - Tips and Tricks
- Topic: Tapered ball mill
- Replies: 20
- Views: 13069
Re: Tapered ball mill
What I was (clumsily) trying to convey by the terms "TBN tool path" and SBN tool path" are the tool paths generated by either using a TBN or SBN as the tool used to generate the machining tool path. What I'm asking is can you use the tool path generated by a SBN tool with a TBN loaded into the spind...
- Sun Feb 18, 2018 4:00 pm
- Forum: Aspire - Tips and Tricks
- Topic: Tapered ball mill
- Replies: 20
- Views: 13069
Re: Tapered ball mill
For scottp55 and/or Leo - where do you get your Chinese TBNs? scottp55 - I checked the website on the side of the container in your picture - it was a dead end. For all - when using a TBN - do you use a tapered BN tool path or a straight BN tool path? My limited experience demonstrated the TBN tool ...
- Sat Feb 17, 2018 3:23 pm
- Forum: VCarve - General
- Topic: Material Setup Using Machine Bed as z-zero
- Replies: 23
- Views: 8311
Re: Material Setup Using Machine Bed as z-zero
Not familiar with your control software but your machine acts as if it thinks your material is thicker than it really is. I'd check your material thickness settings (critically important if zeroing on spoil board, not important if zeroing on surface).
- Fri Feb 16, 2018 4:18 pm
- Forum: VCarve - General
- Topic: Material Setup Using Machine Bed as z-zero
- Replies: 23
- Views: 8311
Re: Material Setup Using Machine Bed as z-zero
Can you set Z zero at the bottom of the pocket?
- Mon Dec 18, 2017 4:11 pm
- Forum: Aspire - Gallery
- Topic: Anniversary
- Replies: 13
- Views: 7959
Re: Anniversary
How did color the lettering?
- Thu Nov 03, 2016 10:38 pm
- Forum: Aspire - Gallery
- Topic: Wooden Clock "Magica", driven by a solenoid coil
- Replies: 8
- Views: 7556
Re: Wooden Clock "Magica", driven by a solenoid coil
Couldn't you just import the PDF file? Aren't they vectors?
- Tue Aug 16, 2016 2:36 pm
- Forum: VCarve - General
- Topic: Fine Engraving
- Replies: 17
- Views: 6975
Re: Fine Engraving
What's the difference between them?
- Thu Mar 24, 2016 3:03 pm
- Forum: VCarve - Tips and Tricks
- Topic: 2D Rope Border
- Replies: 2
- Views: 5318
Re: 2D Rope Border
Look at the "rest machining" tutorial that uses grapes as the subject (can't remember which one it is). There is a technique explained there which uses "create component from preview" then traces the new component to create 2d vectors from a 3d image. Very easy to do, endless possibilities of conver...
- Thu Feb 04, 2016 4:59 pm
- Forum: VCarve - General
- Topic: Feeds and Speeds
- Replies: 14
- Views: 10951
Re: Feeds and Speeds
Any advice on chipload numbers for vbits? Does chipload even matter? I carve at about 20 ipm , 14100rpm with a 2 flute 30 degree vbit with a tip diameter of .005. Chipload calculates out to .0007. Seems like a nonsensical number. Any thoughts? Scott That # only makes sense if the .005" wide part of...
- Thu Feb 04, 2016 1:09 am
- Forum: VCarve - General
- Topic: Feeds and Speeds
- Replies: 14
- Views: 10951
Re: Feeds and Speeds
Any advice on chipload numbers for vbits? Does chipload even matter? I carve at about 20 ipm , 14100rpm with a 2 flute 30 degree vbit with a tip diameter of .005. Chipload calculates out to .0007. Seems like a nonsensical number.
Any thoughts?
Scott
Any thoughts?
Scott
- Sat Sep 12, 2015 3:20 pm
- Forum: VCarve - Gallery
- Topic: Try at vinlay
- Replies: 6
- Views: 4460
Re: Try at vinlay
I'd say it came out well. May I ask, what bit, what start and flat depths?
- Wed Mar 04, 2015 3:57 pm
- Forum: Aspire - Tips and Tricks
- Topic: Squaring up Axis
- Replies: 6
- Views: 5780
Re: Squaring up Axis
Nice technique.
Paul Rowntree does essentially the same thing in software with Skewcalc.
Paul Rowntree does essentially the same thing in software with Skewcalc.
- Thu Jan 22, 2015 8:05 pm
- Forum: Aspire - Gallery
- Topic: New bar at my Golf Club
- Replies: 13
- Views: 6295
Re: New bar at my Golf Club
I'm trying to avoid asking a question which has (probably) already been answered and in my quest I came across this thread and the reference to "video D9, Modelling a Log Cabin." Can't find D9 on my disks or on the Vectric Site. Any help finding it? I'm trying to overlay a texture I created from a ....
- Sun Aug 03, 2014 1:03 am
- Forum: Free CNC Projects
- Topic: Free Project - The Vectricon Chroniker
- Replies: 20
- Views: 22869
Re: Free Project - The Vectricon Chroniker
I think he wrote he was running v4 and wondered why they wouldn't open - the website states for Aspire 3.5 yet apparently they will open in Aspire v4.5, but not v4.
- Tue Jul 22, 2014 3:57 pm
- Forum: Aspire - General
- Topic: Trimming a component
- Replies: 2
- Views: 1787
Re: Trimming a component
Got it. Much appreciated.