Definitely worthy of a thead on its own.BrianM wrote:These were so cool I've split them out from the original topic to this new thread
Brian
Search found 77 matches
- Tue Jul 21, 2009 7:39 pm
- Forum: Aspire - Gallery
- Topic: 3D Door Pulls / Handles
- Replies: 9
- Views: 4553
Re: 3D Door Pulls / Handles
- Tue Jul 21, 2009 7:34 am
- Forum: Aspire - Gallery
- Topic: 3D Door Pulls / Handles
- Replies: 9
- Views: 4553
Re: doorpanel from samplefiles
Hey Victor,
Those pulls look great
Those pulls look great
- Wed Jul 15, 2009 8:29 pm
- Forum: Aspire - General
- Topic: 2 Rail Swwp Problem
- Replies: 14
- Views: 4822
Re: 2 Rail Swwp Problem
Hi Tim,
Thanks for the compliment, I sent the file off to Vectric to see what I have done to cause the problem.
Thanks for the compliment, I sent the file off to Vectric to see what I have done to cause the problem.
- Sun Jul 12, 2009 10:08 pm
- Forum: Aspire - General
- Topic: 2 Rail Swwp Problem
- Replies: 14
- Views: 4822
Re: 2 Rail Swwp Problem
Hi All,
I checked the high point along the moulding, they are constant.
Here is the 2 rails sweep and the section.
I checked the high point along the moulding, they are constant.
Here is the 2 rails sweep and the section.
- Sun Jul 12, 2009 9:33 pm
- Forum: Aspire - General
- Topic: 2 Rail Swwp Problem
- Replies: 14
- Views: 4822
Re: 2 Rail Swwp Problem
Hi Tony,
I am not sure how to check the Z height. The two sweep rail are parallel, I could understand that it could cause the high point to be in the middle, but the high point is near the right hand bend.
Thanks
I am not sure how to check the Z height. The two sweep rail are parallel, I could understand that it could cause the high point to be in the middle, but the high point is near the right hand bend.
Thanks
- Sun Jul 12, 2009 8:48 pm
- Forum: Aspire - General
- Topic: 2 Rail Swwp Problem
- Replies: 14
- Views: 4822
Re: 2 Rail Swwp Problem
The crv3d file is too large to upload
- Sun Jul 12, 2009 8:45 pm
- Forum: Aspire - General
- Topic: 2 Rail Swwp Problem
- Replies: 14
- Views: 4822
Re: 2 Rail Sweep Problem
Hi Victor,
Will this help, the other odd thing is the correct high point is not in the middle.
Is there anything else that would help
Will this help, the other odd thing is the correct high point is not in the middle.
Is there anything else that would help
- Sun Jul 12, 2009 7:50 pm
- Forum: Aspire - General
- Topic: 2 Rail Swwp Problem
- Replies: 14
- Views: 4822
2 Rail Swwp Problem
I have just spent 6 hours machining some shaped handrail using the 2 rail sweep, the finished thickness in the middle is correct but each end is 5mm thinner . The table is flat The material is held down I also checked the scale to exact height with the size. I hope someone can help This is my first ...
- Wed May 06, 2009 9:24 pm
- Forum: Aspire - Gallery
- Topic: Bitmap Texture-Bluegill
- Replies: 7
- Views: 4808
Re: Bitmap Texture-Bluegill
Mike,
That is a great job
That is a great job
- Thu Apr 30, 2009 3:53 pm
- Forum: VCarve - General
- Topic: Baltic Birch ply
- Replies: 3
- Views: 2382
Re: Baltic Birch ply
Hi Andrew,
You could try
Silvermans
Edens
Lathams
Regards
You could try
Silvermans
Edens
Lathams
Regards
- Wed Mar 18, 2009 4:27 pm
- Forum: Aspire - Tips and Tricks
- Topic: Pocket screws
- Replies: 1
- Views: 1966
Pocket screws
If anyone builds cabinets with pocket screw the new fluting function makes it really easy.
Just layout vectors where you want to insert your pocket screw, then use the fluting function with either ramp at start or ramp over complete length.
Just layout vectors where you want to insert your pocket screw, then use the fluting function with either ramp at start or ramp over complete length.
- Tue Mar 17, 2009 8:15 pm
- Forum: Aspire - General
- Topic: Bitmap Trace
- Replies: 4
- Views: 2399
Re: Bitmap Trace
Paul, when you group the vectors the Bitmap layer was the selected layer (even though it was off) so the group would be put on that layer and it would be re-activated. So when you switched the bitmap layer off the group was also on that layer and disappeared. Thanks, James Thanks James Paul, As Tim...
- Tue Mar 17, 2009 7:40 pm
- Forum: Aspire - General
- Topic: Bitmap Trace
- Replies: 4
- Views: 2399
Re: Bitmap Trace
Tim,
The bitmap and the vectors are on seperate layers.
The bitmap and the vectors are on seperate layers.
- Tue Mar 17, 2009 6:48 pm
- Forum: Aspire - General
- Topic: Bitmap Trace
- Replies: 4
- Views: 2399
Bitmap Trace
When I have traced a bitmap with a vector I turn off the bitmap layer, I then select some of the vectors to group them the bitmap layer turns on again, if I turn off the bitmap layer again the vectors disapear with it...What am I doing wrong ?
- Tue Mar 17, 2009 7:53 am
- Forum: Aspire - Tips and Tricks
- Topic: Carved or shaped seat
- Replies: 11
- Views: 9305
Re: Carved or shaped seat
Wes,
You could make them custom fit by using a probe
You could make them custom fit by using a probe