Search found 81 matches

by paul60
Tue Sep 15, 2020 3:03 am
Forum: Control Software related questions
Topic: computer parallel port
Replies: 4
Views: 564

Re: computer parallel port

Barbados
by paul60
Tue Sep 15, 2020 1:04 am
Forum: Control Software related questions
Topic: computer parallel port
Replies: 4
Views: 564

computer parallel port

Hi can anyone recommend where i can purchase a computer with a parallel port. Ebay amazon or anyone that ship outside the USA
best computer brand and model type so i can search from my side.
thanks .
by paul60
Sun Aug 23, 2020 11:18 pm
Forum: VCarve - General
Topic: Dollhouse files
Replies: 3
Views: 309

Dollhouse files

Does anyone know where i can obtain files for dollhouses?
I purchase a couple from Esty both were rubbing never got them to work.
I do not have a problem paying for a good file if it works.
Thanks
by paul60
Mon Jun 22, 2020 6:00 pm
Forum: VCarve - General
Topic: pdf help
Replies: 7
Views: 488

Re: pdf help

Thanks is there someway to convert this to a pdf or dxf?
by paul60
Mon Jun 22, 2020 5:13 pm
Forum: VCarve - General
Topic: pdf help
Replies: 7
Views: 488

pdf help

I am having a problem opening the enclosed pdf files the pdf look correct when i open it as a pdf but not when i open it in vcarve pro
i get just a number of broken lines that i cannot select.
thanks for any help on this
by paul60
Mon Mar 30, 2020 5:28 pm
Forum: VCarve - General
Topic: plexiglass cutting
Replies: 3
Views: 333

Re: plexiglass cutting

thanks Bob what is your ramping settings i also have a shopbot with a spindle
by paul60
Mon Mar 30, 2020 3:07 pm
Forum: VCarve - General
Topic: plexiglass cutting
Replies: 3
Views: 333

plexiglass cutting

i am looking for any suggestions for cutting plexiglass i need to cut 300 8inch circles from 3/8 material
what ramping setting should i try
spindle speed/cutting speed. best type of bit? i have up spiral single flute and up spiral 0 flute 3/8 bits how deep should i cut.
thanks Paul
by paul60
Fri Mar 13, 2020 11:59 pm
Forum: VCarve - General
Topic: cutting aluminum
Replies: 10
Views: 790

Re: cutting aluminum

What is the recommended past depth for 4mm aluminum
what is the correct Ramp setting.
using 6mm spiral cutter
thanks
by paul60
Fri Mar 13, 2020 4:04 pm
Forum: VCarve - General
Topic: cutting aluminum
Replies: 10
Views: 790

cutting aluminum

Does anyone has experience cutting aluminum?
I been asked to cut signs using 3mm aluminum
using a shopbot prt 96 with 3hp spindle.
i am not sure what settings i should be using what type of bits is best
thanks paul
by paul60
Sun Oct 13, 2019 12:50 am
Forum: VCarve - General
Topic: opening file problem
Replies: 3
Views: 740

Re: opening file problem

Thanks everyone i never thought on nodes. yes i dont think its worth it.
by paul60
Sat Oct 12, 2019 5:56 pm
Forum: VCarve - General
Topic: opening file problem
Replies: 3
Views: 740

opening file problem

been trying to open the enclosed file with vcarve 8.5 but no luck
tried with two computers same results.
after i open the zip file i then import the dxf file into vcarve but computers just lock up.
anyone know why?
Paul
by paul60
Mon Sep 30, 2019 3:28 pm
Forum: VCarve - General
Topic: Copy object along vector
Replies: 4
Views: 610

Re: Copy object along vector

Thanks everyone for the help got it now Paul
by paul60
Mon Sep 30, 2019 1:18 am
Forum: VCarve - General
Topic: Copy object along vector
Replies: 4
Views: 610

Copy object along vector

not sure if this is possible. on the attached file i need to copy the .125 hole[ shown on the bottom left of the spiral,] along the centre of the .5 inch width
of the spiral.
thanks
by paul60
Fri Sep 20, 2019 2:08 am
Forum: VCarve - General
Topic: Ramp settings
Replies: 4
Views: 752

Re: Ramp settings

I am cutting half inch pvc board one pass .125 down spiral bit
by paul60
Thu Sep 19, 2019 9:55 pm
Forum: VCarve - General
Topic: Ramp settings
Replies: 4
Views: 752

Re: Ramp settings

Thanks Rcnewcomb what would be your recommended ramp settings for this file
Paul