Search found 31 matches

by makecnc
Sun Mar 08, 2020 3:43 pm
Forum: Aspire - General
Topic: problem with messages etc in forum
Replies: 2
Views: 293

problem with messages etc in forum

Hello, can someone please help i do not seem to be able to send a private message to friends any longer or view profiles of members etc
it now says not authorized for some reason even when logged in?
by makecnc
Sun Dec 08, 2019 2:51 pm
Forum: Cut2D - General
Topic: Support Pages and Frequently Asked Questions
Replies: 164
Views: 1740507

Re: cant see profiles etc

Hello, can someone please help i do not seem to be able to send a private message to friends any long or view profiles of members etc ?
by makecnc
Sun Jan 06, 2019 7:04 pm
Forum: Post Processors
Topic: Needing Post processor for DDCSV 2.1 controller
Replies: 4
Views: 2063

Needing Post processor for DDCSV 2.1 controller

HI all i have found a really nice unit that allows me to control a CNC Router or mill etc without needing an external computer or software like MACH 3 etc it's called DDCSV 2.1 and is available on eBay with an MPG pendant for about $300 shipped MACH 3 alone is $175 not to mention the cost of a compu...
by makecnc
Sun Nov 26, 2017 8:46 pm
Forum: Gadgets - Requests
Topic: Script recorder-player.
Replies: 5
Views: 5199

Re: Script recorder-player.

please excuse my lack of knowledge here on this
but am i to assume i could automate tasks in Autocad using this script as well as Vectric
just would love a bit more info on how it automates vectric task ? what is the basic process ?
by makecnc
Sun Nov 06, 2016 2:17 am
Forum: Aspire - General
Topic: Drawing tools shortcuts ?
Replies: 6
Views: 2202

Re: Drawing tools shortcuts ?

thank you all for your great info i tried both ways of doing things and i have to say i really like the straight lines and then going back in node edit mode and smoothing nodes and making slight final adjustments it does help keep node count down as well as make a much more accurate trace in my opin...
by makecnc
Sat Nov 05, 2016 6:25 pm
Forum: Aspire - General
Topic: Drawing tools shortcuts ?
Replies: 6
Views: 2202

Re: Drawing tools shortcuts ?

Thanks for your reply and info Here is an image of a part of the drawings i am dealing with and this is one of the less complex you can see all the sharp inside points and then right to curves so i hope above hope that Vectric adds the shortcuts in an update or next version as it would make a lot of...
by makecnc
Sat Nov 05, 2016 5:26 pm
Forum: Aspire - General
Topic: Drawing tools shortcuts ?
Replies: 6
Views: 2202

Drawing tools shortcuts ?

Hi all i have a question if anyone could help i am wanting to trace some old public domain fretwork patterns into Aspire they are too far gone for bitmap trace so i have to manually draw them following the outline on the image it seems very tedious to have to use the mouse to change drawing tools al...
by makecnc
Fri Mar 20, 2015 9:17 pm
Forum: VCarve - General
Topic: curve fit tool question
Replies: 8
Views: 1996

Re: curve fit tool question

hmmmn

i just did another test and set the angle to 360 degrees to see what would happen
and it cut the nodes by a ton and did not touch a single critical strait line

so i guess that solves it at least for this one
by makecnc
Fri Mar 20, 2015 8:13 pm
Forum: VCarve - General
Topic: curve fit tool question
Replies: 8
Views: 1996

Re: curve fit tool question

should be fixed now you might need to refresh the page
by makecnc
Fri Mar 20, 2015 7:57 pm
Forum: VCarve - General
Topic: curve fit tool question
Replies: 8
Views: 1996

Re: curve fit tool question

this is not probably the best example but its all i could get quick if you see the strait line is quite long and is turned into two arcs this happens on slots as well that are at angles in many cases if you look at the top image you will see where the strait lines in four places have been turned to ...
by makecnc
Fri Mar 20, 2015 5:38 pm
Forum: VCarve - General
Topic: curve fit tool question
Replies: 8
Views: 1996

curve fit tool question

HI Everyone i have a question that i have been getting from a lot of our customers who use V carve or Aspire ..i hope i can explain it here.... not too good on the email explanations :) many of them use Corel draw with there lasers and are used to drawing in it and have patterns they have made using...
by makecnc
Sun Jul 13, 2014 7:03 pm
Forum: Aspire - General
Topic: SketchUp and VCarve Pro / Aspire
Replies: 14
Views: 10059

Re: SketchUp and VCarve Pro / Aspire

any news on the toolpath corner compensation gadget or the dogbone gadget ? is this going to be released or do we need to look at writing one ?
by makecnc
Fri Jun 06, 2014 5:01 pm
Forum: Aspire - General
Topic: SketchUp and VCarve Pro / Aspire
Replies: 14
Views: 10059

Re: SketchUp and VCarve Pro / Aspire

thanks for that info Adrian

thats got to be about the most important gadget i have seen yet for vectric products as 99% of flatpack pattern tool paths require dogbones
any idea when this will be released on the gadget page ?
by makecnc
Thu Jun 05, 2014 7:01 pm
Forum: Aspire - General
Topic: SketchUp and VCarve Pro / Aspire
Replies: 14
Views: 10059

Re: SketchUp and VCarve Pro / Aspire

HI Brian

can you explain what the new dogbone Gadget does exactly and when it will be released ?

or point us to somewhere for more info on it

thanks
by makecnc
Tue May 20, 2014 4:00 pm
Forum: Aspire - General
Topic: SketchUp and VCarve Pro / Aspire
Replies: 14
Views: 10059

Re: SketchUp and VCarve Pro / Aspire

HI is there a time frame to see this new filleting gadget ? our life here would be seriously changed by such a gadget as we fillet hundreds of projects if and have a 200 job backlog so PLEASE make us a beta Tester :) it would mean we can get twice as many new projects for people to make up on the si...