I’m not sure if this will show up correctly. This is my first attempt at a photo post. New to CNC used VCarve Pro
Search found 14 matches
- Sat Mar 11, 2023 2:17 pm
- Forum: VCarve - Gallery
- Topic: Puppy
- Replies: 5
- Views: 1764
- Thu Feb 09, 2023 9:10 pm
- Forum: VCarve - Gallery
- Topic: Live Edge Cribbage Board
- Replies: 4
- Views: 1943
Re: Live Edge Cribbage Board
This is good work. I do a lot of live she mesquite. What finish did you use?
- Thu Feb 02, 2023 2:04 am
- Forum: VCarve - Gallery
- Topic: Wizard Relief Carving
- Replies: 18
- Views: 17324
Re: Wizard Relief Carving
I’m new to this forum and looking over past posts in the gallery. This is outstanding. I too have started 3D and would be interested to know about longer bits. I don’t recall if you mentioned the type of wood. Spectacular
- Tue Jan 31, 2023 3:18 pm
- Forum: VCarve - General
- Topic: Automatic “clean” tool path added
- Replies: 7
- Views: 1066
Re: Automatic “clean” tool path added
Thanks
I appreciate the tips
I appreciate the tips
- Mon Jan 30, 2023 10:13 pm
- Forum: VCarve - General
- Topic: Automatic “clean” tool path added
- Replies: 7
- Views: 1066
Re: Automatic “clean” tool path added
Outstanding! I recalculated and it deleted the “Clear” paths. Thank you very much.
- Mon Jan 30, 2023 9:57 pm
- Forum: VCarve - General
- Topic: Automatic “clean” tool path added
- Replies: 7
- Views: 1066
Re: Automatic “clean” tool path added
I choose a 1/4 end Mill for the roughing and 1/8 ball nose for the finish followed by a 1/4 end mill again for Profile cut. See attached please. Also do I save and run all 6 listed tool paths for the project?
- Mon Jan 30, 2023 8:03 pm
- Forum: VCarve - General
- Topic: Automatic “clean” tool path added
- Replies: 7
- Views: 1066
Re: Automatic “clean” tool path added
I sit corrected. Yes it reads “Clear” not clean.
- Mon Jan 30, 2023 1:55 am
- Forum: VCarve - General
- Topic: Automatic “clean” tool path added
- Replies: 7
- Views: 1066
Automatic “clean” tool path added
Does VCarve Pro Makerspace 11ish automatically create an additional tool path when calculating? This happened during Roughing and Finish tool paths calculations. In other words an additional tool path auto titled (clean) was added below each of my roughing tool path and Finish tool path. Why?
- Sun Jan 29, 2023 5:21 pm
- Forum: Design & Make Clipart- General
- Topic: Low resolution or am I doing something wrong
- Replies: 10
- Views: 8128
Re: Low resolution or am I doing something wrong
Thanks, Steve. And sorry about the double post... still trying to figure it all out
- Sun Jan 29, 2023 2:48 pm
- Forum: Design & Make Clipart- General
- Topic: Low resolution or am I doing something wrong
- Replies: 10
- Views: 8128
Re: Low resolution or am I doing something wrong
I am interested in seeing the video that was sent as I am having a similar problem with one of the DM 3D models I’m working with. Perhaps I could learn from the video you were sent. Thanks
- Sun Jan 29, 2023 2:48 pm
- Forum: Design & Make Clipart- General
- Topic: Low resolution or am I doing something wrong
- Replies: 10
- Views: 8128
Re: Low resolution or am I doing something wrong
I am interested in seeing the video that was sent as I am having a similar problem with one of the DM 3D models I’m working with. Perhaps I could learn from the video you were sent. Thanks
- Thu Jan 26, 2023 11:43 pm
- Forum: Design & Make Clipart- General
- Topic: Let's ride!
- Replies: 3
- Views: 5783
Re: Let's ride!
Thanks, Todd.
- Tue Jan 24, 2023 4:41 am
- Forum: VCarve - Gallery
- Topic: Live edge carving
- Replies: 5
- Views: 1952
Re: Live edge carving
I enjoy live edge. Nice carve! I have a lot of live edge mesquite that I’m worried about my feeds and speeds. It’s such a hard wood.
- Mon Jan 23, 2023 5:41 pm
- Forum: Design & Make Clipart- General
- Topic: Let's ride!
- Replies: 3
- Views: 5783
Re: Let's ride!
Hello, I’m new to this forum and new to CNC and Vectric. My first purchases from VCarve clipart include Let’s Ride 1 & 2. The knuckle head and pan head motors are great. Do you know if other (newer) Harley model motors are available too? Specifically, the Twin Cam, and shovel head, or the others. If...