@ adze, this was exactly what happened.
Thank you Jim for your hard work.
It should work now
Benjamin
Search found 28 matches
- Tue Jun 28, 2022 6:22 am
- Forum: Gadgets - User Submissions
- Topic: Easy MDF Cabinet Door Maker
- Replies: 108
- Views: 104192
- Thu Jun 23, 2022 6:42 am
- Forum: Gadgets - User Submissions
- Topic: Easy MDF Cabinet Door Maker
- Replies: 108
- Views: 104192
Re: Easy MDF Cabinet Door Maker
@jimandi If i open the Gadget and select the Door Panel Pocket Bit in the Bit selection page to be a 8mm End mill, and press build and then generate the Toolpaths, the Drawing is fine and the Toolpaths are fine too. If i again enter the Gadget and press build and then Toolpath, i get an error messag...
- Wed Jun 22, 2022 6:31 am
- Forum: Gadgets - User Submissions
- Topic: Easy MDF Cabinet Door Maker
- Replies: 108
- Views: 104192
Re: Easy MDF Cabinet Door Maker
@Jimandi, i see your point. I think right now, optionally, making the outer pocket vector smaller by the depth of cut. And to manually change the 'Door Inside Edge' to Inside. But honestly, i suggest leaving it as is, is the best choice. There are other more important matters than this. It's not har...
- Tue Jun 21, 2022 6:49 am
- Forum: Gadgets - User Submissions
- Topic: Easy MDF Cabinet Door Maker
- Replies: 108
- Views: 104192
Re: Easy MDF Cabinet Door Maker
Sure can. It was just a question out of curiosity. I think the sharp corner effect is the most used Door Front style i know of. There are some pictures i took, i hope it is understandable. Here is a picture of the Shaker now as it is. The Inner Edge of the carving is rounded up in the corners: Simpl...
- Mon Jun 20, 2022 9:37 am
- Forum: Gadgets - User Submissions
- Topic: Easy MDF Cabinet Door Maker
- Replies: 108
- Views: 104192
Re: Easy MDF Cabinet Door Maker
Wow Jim, your work is great. Haven't been in for a while, but this thing evolved really fast. @Sharkcutup, i see that in the picture above you have generated a Kitchen Sink Cabinet with the Interior as a Shaker style, where the Inner edge and the Raised Panel edge are sharp corners. How did you do i...
- Mon Mar 07, 2022 7:39 am
- Forum: Gadgets - User Submissions
- Topic: Easy BoxJoint Maker 3.2
- Replies: 19
- Views: 19133
Re: Easy BoxJoint Maker 3.2
I see what you did there!
Yes that would be, what i thought about. For Drawers and Boxes.
Benjamin
Yes that would be, what i thought about. For Drawers and Boxes.
Benjamin
- Fri Mar 04, 2022 3:15 pm
- Forum: Gadgets - User Submissions
- Topic: Easy BoxJoint Maker 3.2
- Replies: 19
- Views: 19133
Re: Easy BoxJoint Maker 3.2
Has anyone seen WoodSmiths video of Joinery? https://www.youtube.com/watch?v=_ln9McUHV9s&t=434s&ab_channel=Woodsmith He show a great way of making Box Joints with a TBone but Blind ones. From minute 7 onwards You think the Gadget could do such things?? This means, the Joint is Hidden from the inside...
- Thu Feb 24, 2022 7:19 am
- Forum: Gadgets - User Submissions
- Topic: Easy Cabinet Maker
- Replies: 450
- Views: 366833
Re: Easy Cabinet Maker
Here i put up a Screenshot. When im Imperial Measuring System it works nice and Gadget is opening, the way it should be.
When in Metric i get this Error Message:
Benjamin
When in Metric i get this Error Message:
Benjamin
- Wed Feb 23, 2022 8:41 am
- Forum: Gadgets - User Submissions
- Topic: Easy Cabinet Maker
- Replies: 450
- Views: 366833
Re: Easy Cabinet Maker
Wow Great Gadget. I guess this took a very long time until it got finished. Jimandi, you're highly esteemed.
Sadly it's only Imperial and not working in Metric.
Benjamin
Sadly it's only Imperial and not working in Metric.
Benjamin
- Wed Feb 23, 2022 8:05 am
- Forum: Gadgets - User Submissions
- Topic: Easy MDF Cabinet Door Maker
- Replies: 108
- Views: 104192
Re: Easy MDF Cabinet Door Maker
Hello Jimandi. It took me some time to test and to get myself informed about the Scribe Lines. For them to look good, and to be correct, they are not allowed to be 4 lines in each Scribe Corner, but 2 Lines that go like this: Left one from Top to Bottom and the Right one from Bottom to Top. Untitled...
- Fri Feb 11, 2022 2:39 pm
- Forum: Gadgets - User Submissions
- Topic: Easy MDF Cabinet Door Maker
- Replies: 108
- Views: 104192
Re: Easy MDF Cabinet Door Maker
Wonderful good day, Sorry for writing so late... Ok, I've tested the new Gadget, here is a Screenshot. Now the Line Start Points are like this: Upper Left: From Down to Up Upper Right: From Down to Up Lower Left: From Up to Down Lower Right : From Up to Down But they should be like this: Upper Left ...
- Tue Feb 08, 2022 10:51 am
- Forum: Gadgets - User Submissions
- Topic: Easy MDF Cabinet Door Maker
- Replies: 108
- Views: 104192
Re: Easy MDF Cabinet Door Maker
Hello Jimandi, Wow, you work really fast. Thanks a lot for the new Version. I've tested it for the first time. Looks good. There is a little error though, namely the lines all have the Start points from Up to Down, so if you want to create a Toolpath, then you'll have to select a Outside Profile cut...
- Thu Feb 03, 2022 1:31 pm
- Forum: Gadgets - User Submissions
- Topic: Easy MDF Cabinet Door Maker
- Replies: 108
- Views: 104192
Re: Easy MDF Cabinet Door Maker
Would it be possible to add something like the Flutes, but between the Inside Corners and the Exterior, so it looks like it's a real Wooden Door Front? Something like this:
Benjamin
This would also need a separate Layer Name....Benjamin
- Mon Aug 16, 2021 1:58 pm
- Forum: Wrapped Rotary Machining
- Topic: Rotary Machining Rounding Toolpath
- Replies: 7
- Views: 12320
Re: Rotary Machining Rounding Toolpath
Seeing your video, shows that the Radial Strategy has the same finish as mine. So it's not just me. For someone not having a Lathe but a Router with an indexer i guess best strategy is Spiral Cut with a Bit as big as possible.
Thank you for your time and help.
GBU Benjamin
Thank you for your time and help.
GBU Benjamin
- Fri Aug 13, 2021 6:43 am
- Forum: Wrapped Rotary Machining
- Topic: Rotary Machining Rounding Toolpath
- Replies: 7
- Views: 12320
Re: Rotary Machining Rounding Toolpath
@ SteveNelson46: Thank you for the hint. Head and Tailstock are alined perfectly though. The Laserpointer idea is great. @Charlie_I: Like i said, it's not from the Spindle. Perfectly alined also. @ adze_cnc: You were right!!! It is the Router Bit. It seems to curve itself to the outside. so it is 1m...