Search found 17 matches

by Hoosterw
Sun Jan 03, 2021 9:58 am
Forum: Aspire - Tips and Tricks
Topic: Cursor/scrollwheel behaviour haywire
Replies: 6
Views: 1039

Re: Cursor/scrollwheel behaviour haywire

The drivers were up to date, thanks.

But apparently the setting use graphical tablet was set to YES, setting to NO did it for now.

Thanks Adrian.

regards Hans
by Hoosterw
Sat Jan 02, 2021 8:49 pm
Forum: Aspire - Tips and Tricks
Topic: Cursor/scrollwheel behaviour haywire
Replies: 6
Views: 1039

Re: Cursor/scrollwheel behaviour haywire

Just thought to give it a bump.
by Hoosterw
Sat Jan 02, 2021 1:58 pm
Forum: Aspire - General
Topic: Height issue after tool exchange between 3D rough and finish
Replies: 14
Views: 962

Re: Height issue after tool exchange between 3D rough and finish

Dear randall, thank you very much for the help, the issue has been resolved. Running the other post processor was the solutiuon

Rgds Hans
by Hoosterw
Fri Jan 01, 2021 8:58 pm
Forum: Aspire - General
Topic: Height issue after tool exchange between 3D rough and finish
Replies: 14
Views: 962

Re: Height issue after tool exchange between 3D rough and finish

OK, I will save the toolpath using the new postprocessor and run the files again tomorrow.
I need 2 extra models anyway.

Thanks for helping sofar. rgds Hans.
by Hoosterw
Fri Jan 01, 2021 8:37 pm
Forum: Aspire - General
Topic: Height issue after tool exchange between 3D rough and finish
Replies: 14
Views: 962

Re: Height issue after tool exchange between 3D rough and finish

Error 20 is unknown command for my controller
by Hoosterw
Fri Jan 01, 2021 8:00 pm
Forum: Aspire - General
Topic: Height issue after tool exchange between 3D rough and finish
Replies: 14
Views: 962

Re: Height issue after tool exchange between 3D rough and finish

I am looking at the T1M6 code. That seems a tool change code.
When looking at the processed file it gives an error:20.
by Hoosterw
Fri Jan 01, 2021 7:58 pm
Forum: Aspire - General
Topic: Height issue after tool exchange between 3D rough and finish
Replies: 14
Views: 962

Re: Height issue after tool exchange between 3D rough and finish

These are the first. all the same afterwards so less then 50.

T1M6
G17
G0Z20.000
G0X0.000Y0.000S12000M3
G0X124.892Y0.178Z5.000
G1Z-1.250F240.0
G1X127.889Y0.194F720.0
X132.324Y0.258
X120.441Y0.268
X116.959Y0.338
X136.214Y0.348
by Hoosterw
Fri Jan 01, 2021 6:21 pm
Forum: Aspire - General
Topic: Height issue after tool exchange between 3D rough and finish
Replies: 14
Views: 962

Re: Height issue after tool exchange between 3D rough and finish

Not likely. It came about when I started a whole new design and file in Aspire. I ran an imported file from Artcam (my previous design software) and that was ok. Before using Aspire I ran Artcam files on the machine and these never had the problem. So it doen't look like the control software. Thanks...
by Hoosterw
Fri Jan 01, 2021 4:56 pm
Forum: Aspire - General
Topic: Height issue after tool exchange between 3D rough and finish
Replies: 14
Views: 962

Re: Height issue after tool exchange between 3D rough and finish

Sorry, its a engraving V-bit with a flat spot yes. I checked the tools and they seem ok. and yes I am zeroing height at an untouched part of the piece in both cases in the same place. As there are more toolpaths then these (also cut outs) I zero of on the same place multpile times. I even check cali...
by Hoosterw
Fri Jan 01, 2021 3:19 pm
Forum: Aspire - General
Topic: Height issue after tool exchange between 3D rough and finish
Replies: 14
Views: 962

Height issue after tool exchange between 3D rough and finish

I am experiencing a height issue after a tools exchange between roughing 3D toolpath and the finish toolpath. When I do the roughening with an 1mm endmill and I exchange to a 20degrees 0.1V-bit tool I set the height again using the Z probe but when it starts, its off by a tenth or so and runs above ...
by Hoosterw
Wed Dec 23, 2020 8:56 am
Forum: Aspire - Tips and Tricks
Topic: Cursor/scrollwheel behaviour haywire
Replies: 6
Views: 1039

Re: Cursor/scrollwheel behaviour haywire

Thanks, but its a Wacom tablet mouse. So unlikely it will be the problem.

As said it happens when I have had a preview of the toolpath. when I want to click and drag the model in 3D view it changes its orientation upon the click.
by Hoosterw
Tue Dec 22, 2020 10:07 pm
Forum: Aspire - Tips and Tricks
Topic: Cursor/scrollwheel behaviour haywire
Replies: 6
Views: 1039

Cursor/scrollwheel behaviour haywire

After toolpath previewing the cursor in the 3D view map is going haywire or at least the 3D object skirts and swipes around when pointing and clicking and its hard to get the behavior as before. I have to go out of the model and re open and the behavior is normal.

Any way to keep this from happening?
by Hoosterw
Sat Dec 19, 2020 10:43 am
Forum: Aspire - General
Topic: Newbi 3D relief issue.
Replies: 4
Views: 389

Re: Newbi 3D relief issue.

Thanks Steve. I will bear it in mind.
by Hoosterw
Fri Dec 18, 2020 9:46 pm
Forum: Aspire - General
Topic: Newbi 3D relief issue.
Replies: 4
Views: 389

Re: Newbi 3D relief issue.

Thanks Joe. Its all made from 2D up with vectors so that might be relative easy. I will give it a try.

Although it gives no clue as to why they occur. which IMHO they shouldn't.