Search found 10 matches
- Wed Sep 07, 2022 5:40 pm
- Forum: VCarve - General
- Topic: VCarve Pro Adding and Deleting Materials in the Material Setting Section
- Replies: 8
- Views: 1757
Re: VCarve Pro Adding and Deleting Materials in the Material Setting Section
Adrian thank you just what i was looking to do thanks again for your help
- Wed Sep 07, 2022 5:16 pm
- Forum: VCarve - General
- Topic: VCarve Pro Adding and Deleting Materials in the Material Setting Section
- Replies: 8
- Views: 1757
Re: VCarve Pro Adding and Deleting Materials in the Material Setting Section
<blush> I need to read carefully before I respond. :oops: :oops: :oops: </blush> No you had it right the first time, when i open the application data folder and go to bitmap file i don't see it in there. So i'm trying to delete the words Bamboo in the drop down material setting menu. thanks Bob
- Sat Sep 03, 2022 5:12 pm
- Forum: VCarve - General
- Topic: VCarve Pro Adding and Deleting Materials in the Material Setting Section
- Replies: 8
- Views: 1757
Re: VCarve Pro Adding and Deleting Materials in the Material Setting Section
Hello Randell thanks for the reply I've tried that but it's not showing up. But when i open the material settings tab you can see that i have added the word Bamboo this is were I'm trying to edit. Thanks again Bob843
- Fri Sep 02, 2022 9:44 pm
- Forum: VCarve - General
- Topic: VCarve Pro Adding and Deleting Materials in the Material Setting Section
- Replies: 8
- Views: 1757
VCarve Pro Adding and Deleting Materials in the Material Setting Section
Can anyone point me in the right direction I'm trying to delete a new material (Bamboo) i placed in the wrong section, on the job set up pane under Material Settings
- Fri Jun 19, 2020 7:21 pm
- Forum: Control Software related questions
- Topic: mach 3 and vcarve pro
- Replies: 8
- Views: 8657
Re: mach 3 and vcarve pro
ger21 what is the fix for this?? i liked that post processor even though i don't have a ATC on my machine
it stops and will let me do a manual change
it stops and will let me do a manual change
- Thu Jun 18, 2020 10:43 pm
- Forum: Control Software related questions
- Topic: mach 3 and vcarve pro
- Replies: 8
- Views: 8657
Re: mach 3 and vcarve pro
okay i found
If a job actually takes 6 minutes to cut and the estimate was 3 minutes, the scale factor would be set to 2 (actual time / estimated time = 6/3).
If a job actually takes 6 minutes to cut and the estimate was 3 minutes, the scale factor would be set to 2 (actual time / estimated time = 6/3).
- Thu Jun 18, 2020 10:34 pm
- Forum: Control Software related questions
- Topic: mach 3 and vcarve pro
- Replies: 8
- Views: 8657
Re: mach 3 and vcarve pro
I'm not sure, I'll have to do some research.. a hint were to get started would be cool if you have the time , thanks Bob
- Wed Jun 17, 2020 9:22 pm
- Forum: Control Software related questions
- Topic: mach 3 and vcarve pro
- Replies: 8
- Views: 8657
Re: mach 3 and vcarve pro
Thanks that worked well, I also found that PathPilot(inch)(.nc) seemed to work. Now i have to work on the speed problem used an old design with a good known cut time but when i run it with the vcarve program its doubles the cut time.
- Fri Jun 12, 2020 9:49 pm
- Forum: Control Software related questions
- Topic: mach 3 and vcarve pro
- Replies: 8
- Views: 8657
mach 3 and vcarve pro
hello all new to vcarve software, i could not find my exact machine in the post processor drop down but found one that works with mach 3, G-Code ATC (inch)(*.Tap) on a trial program run i get an error message TO FAST FOR PULLEY ! USING MAX the trial program runs ok but i would like to make a run on ...
- Fri Jun 12, 2020 9:14 pm
- Forum: Cut2D - General
- Topic: The New Map Thread - Show us where you are in the world
- Replies: 1441
- Views: 4393670
Re: The New Map Thread - Show us where you are in the world
Bob C
V Carve Pro
Murrells Inlet, South Carolina
V Carve Pro
Murrells Inlet, South Carolina