Moulding. not Modeling!!!
I think I can do that!!
Thanks again
Search found 11 matches
- Wed Feb 03, 2021 3:39 am
- Forum: Cut2D - General
- Topic: Support Pages and Frequently Asked Questions
- Replies: 223
- Views: 2996677
- Wed Feb 03, 2021 3:35 am
- Forum: Cut2D - General
- Topic: Support Pages and Frequently Asked Questions
- Replies: 223
- Views: 2996677
Re: Support Pages and Frequently Asked Questions
Gonna be a looong time before I reach "vectric wizard" status!!!
- Wed Feb 03, 2021 3:32 am
- Forum: Cut2D - General
- Topic: Support Pages and Frequently Asked Questions
- Replies: 223
- Views: 2996677
Re: Support Pages and Frequently Asked Questions
Can't figure it out. And I did a few tutorials (wrong ones). spent a couple hours in Modeling. Not enough experience in there.
Can you give me a few hints?
Thanks
Jane
Can you give me a few hints?
Thanks
Jane
- Wed Feb 03, 2021 3:26 am
- Forum: Cut2D - General
- Topic: Support Pages and Frequently Asked Questions
- Replies: 223
- Views: 2996677
Re: Support Pages and Frequently Asked Questions
Exactly like that! slightly different dimensions
- Wed Feb 03, 2021 2:27 am
- Forum: Cut2D - General
- Topic: Support Pages and Frequently Asked Questions
- Replies: 223
- Views: 2996677
Re: Support Pages and Frequently Asked Questions
Question: I have watched tutorials and cannot figure out how to insert a slot/handle in a board. It may help if I tell you exactly what I am making - a large tray for a 50" square ottoman. I want to round off the tops of the 4 sides and also place a slot in each side for fingers in order to pick up ...
- Mon May 11, 2020 6:05 pm
- Forum: Aspire - General
- Topic: programming
- Replies: 6
- Views: 2062
Re: programming
Thanks so much, John! aka highpockets!!! I get it with your explanation and examples. I will do that pattern. I've watched many tutorials! (that's not the advise I needed!!) It still seems to me that using the cut on the inside/outside of the vectors should get the same results. So then why did it c...
- Sun May 10, 2020 9:13 pm
- Forum: Aspire - General
- Topic: programming
- Replies: 6
- Views: 2062
programming
2020-05-10 (1).png I've attached a few screenshots of a project that I can't seem to get the toolpath to complete. Would someone please tell me what I need to different. I have tried with multiple tools, and it doesn't seem to make a difference. I have also included a pic of a completed piece that ...
- Mon Apr 27, 2020 11:15 pm
- Forum: Aspire - General
- Topic: Tutorial
- Replies: 3
- Views: 1507
Re: Tutorial
YESSSSSS
thanks so much!
thanks so much!
- Sun Apr 26, 2020 11:05 pm
- Forum: Aspire - General
- Topic: Tutorial
- Replies: 3
- Views: 1507
Tutorial
Would someone please help me find a particular tutorial. I have actually watched it twice now, once when I first got my machine, and once the other day (when I just happened upon it). I tried yesterday to watch it again, and couldn't find it. It is a 3d file with the Wildlife Collection, and it is a...
- Mon Apr 20, 2020 2:01 pm
- Forum: Aspire - General
- Topic: Preview vs programming
- Replies: 3
- Views: 1359
Re: Preview vs programming
Thank you. I had closed the file last night. Just now when I went back and re-ran it, so that I could send it with this reply, the preview was just the way it was supposed to be!! Ta Da! Wish I knew what I had in there extra! So if I need to send other questions, which I most certainly will!, do I a...
- Mon Apr 20, 2020 3:10 am
- Forum: Aspire - General
- Topic: Preview vs programming
- Replies: 3
- Views: 1359
Preview vs programming
On my project, I have done a pocket area to a depth of 0.21 After that is cut, I have added a vcarve 60 degree with a flat depth of 0.31, with Z0 at the original surface, expecting my bit to cut 0.10 into the new surface. When I calculate and look at the 3D preview and put my cursor on the deepest a...