Search found 11 matches

by jmoyer
Wed Feb 03, 2021 3:39 am
Forum: Cut2D - General
Topic: Support Pages and Frequently Asked Questions
Replies: 181
Views: 1859581

Re: Support Pages and Frequently Asked Questions

Moulding. not Modeling!!!
I think I can do that!!
Thanks again
by jmoyer
Wed Feb 03, 2021 3:35 am
Forum: Cut2D - General
Topic: Support Pages and Frequently Asked Questions
Replies: 181
Views: 1859581

Re: Support Pages and Frequently Asked Questions

Gonna be a looong time before I reach "vectric wizard" status!!!
by jmoyer
Wed Feb 03, 2021 3:32 am
Forum: Cut2D - General
Topic: Support Pages and Frequently Asked Questions
Replies: 181
Views: 1859581

Re: Support Pages and Frequently Asked Questions

Can't figure it out. And I did a few tutorials (wrong ones). spent a couple hours in Modeling. Not enough experience in there.
Can you give me a few hints?
Thanks
Jane
by jmoyer
Wed Feb 03, 2021 3:26 am
Forum: Cut2D - General
Topic: Support Pages and Frequently Asked Questions
Replies: 181
Views: 1859581

Re: Support Pages and Frequently Asked Questions

Exactly like that! slightly different dimensions
by jmoyer
Wed Feb 03, 2021 2:27 am
Forum: Cut2D - General
Topic: Support Pages and Frequently Asked Questions
Replies: 181
Views: 1859581

Re: Support Pages and Frequently Asked Questions

Question: I have watched tutorials and cannot figure out how to insert a slot/handle in a board. It may help if I tell you exactly what I am making - a large tray for a 50" square ottoman. I want to round off the tops of the 4 sides and also place a slot in each side for fingers in order to pick up ...
by jmoyer
Mon May 11, 2020 6:05 pm
Forum: Aspire - General
Topic: programming
Replies: 6
Views: 822

Re: programming

Thanks so much, John! aka highpockets!!! I get it with your explanation and examples. I will do that pattern. I've watched many tutorials! (that's not the advise I needed!!) It still seems to me that using the cut on the inside/outside of the vectors should get the same results. So then why did it c...
by jmoyer
Sun May 10, 2020 9:13 pm
Forum: Aspire - General
Topic: programming
Replies: 6
Views: 822

programming

2020-05-10 (1).png I've attached a few screenshots of a project that I can't seem to get the toolpath to complete. Would someone please tell me what I need to different. I have tried with multiple tools, and it doesn't seem to make a difference. I have also included a pic of a completed piece that ...
by jmoyer
Mon Apr 27, 2020 11:15 pm
Forum: Aspire - General
Topic: Tutorial
Replies: 3
Views: 618

Re: Tutorial

YESSSSSS
thanks so much!
by jmoyer
Sun Apr 26, 2020 11:05 pm
Forum: Aspire - General
Topic: Tutorial
Replies: 3
Views: 618

Tutorial

Would someone please help me find a particular tutorial. I have actually watched it twice now, once when I first got my machine, and once the other day (when I just happened upon it). I tried yesterday to watch it again, and couldn't find it. It is a 3d file with the Wildlife Collection, and it is a...
by jmoyer
Mon Apr 20, 2020 2:01 pm
Forum: Aspire - General
Topic: Preview vs programming
Replies: 3
Views: 518

Re: Preview vs programming

Thank you. I had closed the file last night. Just now when I went back and re-ran it, so that I could send it with this reply, the preview was just the way it was supposed to be!! Ta Da! Wish I knew what I had in there extra! So if I need to send other questions, which I most certainly will!, do I a...
by jmoyer
Mon Apr 20, 2020 3:10 am
Forum: Aspire - General
Topic: Preview vs programming
Replies: 3
Views: 518

Preview vs programming

On my project, I have done a pocket area to a depth of 0.21 After that is cut, I have added a vcarve 60 degree with a flat depth of 0.31, with Z0 at the original surface, expecting my bit to cut 0.10 into the new surface. When I calculate and look at the 3D preview and put my cursor on the deepest a...