Search found 601 matches

by scotttarnor
Sun Sep 19, 2021 4:49 pm
Forum: Aspire - General
Topic: Creating a component that the modeling tool will accept
Replies: 6
Views: 144

Re: Creating a component that the modeling tool will accept

If you could share your file it would help, without it we would be guessing.
by scotttarnor
Mon Sep 13, 2021 4:18 am
Forum: Aspire - Gallery
Topic: It's all in the eyes....
Replies: 9
Views: 508

Re: It's all in the eyes....

Wow! That looks awesome!
by scotttarnor
Mon Sep 13, 2021 3:51 am
Forum: Aspire - General
Topic: Post processor for lazer
Replies: 5
Views: 139

Re: Post processor for lazer

Try creating the laser as an engraving bit instead of an end mill.
by scotttarnor
Sun Sep 12, 2021 11:54 pm
Forum: VCarve - General
Topic: Installing Laser Module on Desktop V11.07
Replies: 9
Views: 230

Re: Installing Laser Module on Desktop V11.07

I have limited time on my laser but playing around with Nextwaves ready to raster laser software and getting ok results, I have not dedicated the time to dial in power and feed rates yet.
by scotttarnor
Sun Sep 12, 2021 11:36 pm
Forum: VCarve - General
Topic: Installing Laser Module on Desktop V11.07
Replies: 9
Views: 230

Re: Installing Laser Module on Desktop V11.07

I’m sure it’s compatible with V11, it is also not compatible with the Nextwave PP, on the product page Nextwave is not listed. and if you search this forum you can read issues others have had with Sharks/Nextwave.
by scotttarnor
Sun Sep 12, 2021 11:32 pm
Forum: Laser Module - General
Topic: Desktop V-Carve V11.07 Photo Laser Tool
Replies: 3
Views: 224

Re: Desktop V-Carve V11.07 Photo Laser Tool

Can you run the photo with the engraving tool path following the steps Nextwave provides?
The Laser module does not list Nextwave as “ compatible” hardware. There where discussions about Nextwave in this forum, you could search and see what issues others had with the module.
by scotttarnor
Fri Sep 10, 2021 4:53 pm
Forum: VCarve - Gallery
Topic: Another carved Turned Box
Replies: 2
Views: 256

Re: Another carved Turned Box

Beautiful work!
by scotttarnor
Thu Sep 09, 2021 9:03 pm
Forum: VCarve - General
Topic: Laser runs with a delay
Replies: 6
Views: 181

Re: Laser runs with a delay

There were discussions on the forum about the Nextwave PP, I don’t remember what the actual reported issues were but it boils down to the Laser add on does not have Nextwave listed as compatible hardware. If I remember correctly Nextwave stated to use their Ready to Raster program. You could search ...
by scotttarnor
Wed Sep 01, 2021 7:31 pm
Forum: VCarve - General
Topic: VCarve Desktop 11 and NWA's Ready2Control
Replies: 24
Views: 647

Re: VCarve Desktop 11 and NWA's Ready2Control

"If you are using a pendant and you are sure you are using inch PP I would contact Nextwave as there have been similar problems reported in the past on the Shark forum and they were resolve by correcting settings on the pendant.
[/quote]
by scotttarnor
Tue Aug 31, 2021 9:32 pm
Forum: VCarve - General
Topic: VCarve Desktop 11 and NWA's Ready2Control
Replies: 24
Views: 647

Re: VCarve Desktop 11 and NWA's Ready2Control

According to the Nextwave web site you are using the wrong PP, the attached picture of their website states PP “Next Wave CNC inch” or Next Wave CNC MM”
For any thing above version 10.5
by scotttarnor
Tue Aug 31, 2021 2:59 am
Forum: VCarve - General
Topic: VCarve Desktop 11 and NWA's Ready2Control
Replies: 24
Views: 647

Re: VCarve Desktop 11 and NWA's Ready2Control

Nextwave updated their PP back with 10.5 I believe it was, here is a link to the page with current PP, although it should be in the Vectric software. The message you are getting is telling you there is a newer PP. https://nextwaveautomation.zendesk.com/hc/en-us/articles/360046235651 You should reall...
by scotttarnor
Mon Aug 30, 2021 2:17 pm
Forum: VCarve - General
Topic: VCarve Desktop 11 and NWA's Ready2Control
Replies: 24
Views: 647

Re: VCarve Desktop 11 and NWA's Ready2Control

If there's a way to go from VCarve (final drawing) to the CNC machine (in this case, A NWA Shark SD100)? I'm not about to invest thousands of $$ for CAM, but am having trouble taking the GCode to NWA's post-processor, Ready2Control. Somehow, one of the programs is getting confused between millimete...
by scotttarnor
Sat Aug 28, 2021 5:37 pm
Forum: Aspire - General
Topic: Possible help for VCarve users?
Replies: 8
Views: 330

Re: Possible help for VCarve users?

You can not do what you are asking per the user agreement
by scotttarnor
Fri Aug 27, 2021 10:03 pm
Forum: VCarve - Gallery
Topic: Vectric Pro Projects
Replies: 5
Views: 467

Re: Vectric Pro Projects

I really like your chicken sign! Nice work!