I do not do step 4
Jig is fixed location
Search found 12 matches
- Fri Mar 25, 2022 6:47 pm
- Forum: Aspire - General
- Topic: two side machining error
- Replies: 31
- Views: 9995
- Fri Mar 25, 2022 12:53 pm
- Forum: Aspire - General
- Topic: two side machining error
- Replies: 31
- Views: 9995
Re: two side machining error
The Zero X and Y use optical sensors.
If I do the cuts strictly from the top side with two files instead of one everything aligns.
The cuts are with a whiteside RU4700.
What is very interesting is the Y axis does not have this issue.
If I do the cuts strictly from the top side with two files instead of one everything aligns.
The cuts are with a whiteside RU4700.
What is very interesting is the Y axis does not have this issue.
- Thu Mar 24, 2022 10:10 pm
- Forum: Aspire - General
- Topic: two side machining error
- Replies: 31
- Views: 9995
Re: two side machining error
It is square within .003 .
The error is .25 inches in x direction only.
I am going to check on machine and see if I can manually move the x zero point and then report back here.
Odd that the software shows perfect alignment but machining does not match.
The error is .25 inches in x direction only.
I am going to check on machine and see if I can manually move the x zero point and then report back here.
Odd that the software shows perfect alignment but machining does not match.
- Thu Mar 24, 2022 8:38 pm
- Forum: Aspire - General
- Topic: two side machining error
- Replies: 31
- Views: 9995
Re: two side machining error
This is a square piece. I set the piece against the lower left corner. I flip it left/right no dowels. The part is register left and down. When I start cutting it appears that the software is shifting to the right so the bit does not go negative to the through cut for my slot. When I preview the cod...
- Thu Mar 24, 2022 6:10 pm
- Forum: Aspire - General
- Topic: two side machining error
- Replies: 31
- Views: 9995
Re: two side machining error
I am having this error of being off in the x-direction. Vcarve v11. Drawing is in attachement Speaker backbox test pieces.pdf I am flipping the piece horizontal. The one box is a recess and goes pass the 0 point so the cutter can provide a clean cut. Is the program shifting this bottom over to get t...
- Mon Apr 05, 2021 2:37 pm
- Forum: VCarve - General
- Topic: Can I move a start point on a toolpath?
- Replies: 15
- Views: 3797
Re: Can I move a start point on a toolpath?
I confirmed that at least for my machine (Axiom) the quick engrave toolpath does not work properly for outline of lettering. When I used the profile toolpath everything works as expected.
Thanks for all the help.
Thanks for all the help.
- Thu Apr 01, 2021 6:04 pm
- Forum: VCarve - General
- Topic: Can I move a start point on a toolpath?
- Replies: 15
- Views: 3797
Re: Can I move a start point on a toolpath?
Okay I am using an end mill toolpath modified to the Laser. This was what Jtech told me to do. Looking for the area to change what you have suggested....very sorry to not be getting this. I put a short drawing file in a response with just one word. Quick engrave is the toolpath selected. I found it!...
- Thu Apr 01, 2021 5:34 pm
- Forum: VCarve - General
- Topic: Can I move a start point on a toolpath?
- Replies: 15
- Views: 3797
Re: Can I move a start point on a toolpath?
I read the instruction on node editing which I have done before. However the starting point I put in didn't seem to change the location....looking at this further.
When I reduced the file down I noticed the starting point moved for the "e" however the "w" looks in the same spot.
When I reduced the file down I noticed the starting point moved for the "e" however the "w" looks in the same spot.
- Thu Apr 01, 2021 3:07 pm
- Forum: VCarve - General
- Topic: Can I move a start point on a toolpath?
- Replies: 15
- Views: 3797
Re: Can I move a start point on a toolpath?
Yes I did the vector validator and okay. drawing file is too large to post I guess. (6 Meg)
Seems to be start point is an acute angle 90 degrees or less.
Seems to be start point is an acute angle 90 degrees or less.
- Thu Apr 01, 2021 2:23 pm
- Forum: VCarve - General
- Topic: Can I move a start point on a toolpath?
- Replies: 15
- Views: 3797
Re: Can I move a start point on a toolpath?
Okay I think this problem I have is related to the start point being put in the wrong place. Though not sure.
Guidance? I am using a laser on my CNC Axiom pro
Guidance? I am using a laser on my CNC Axiom pro
- Sun Jul 21, 2019 1:34 am
- Forum: Cut2D - General
- Topic: Support Pages and Frequently Asked Questions
- Replies: 223
- Views: 2997827
Re: Support Pages and Frequently Asked Questions
Never mind figured it out using the form tool function.
Roydan
Roydan
- Sat Jul 20, 2019 5:32 pm
- Forum: Cut2D - General
- Topic: Support Pages and Frequently Asked Questions
- Replies: 223
- Views: 2997827
Re: Support Pages and Frequently Asked Questions
Is there a way to import a bit profile that is different from the standard tools listed?
An example is a whiteside SC55 engraving bit but with a 45Deg point on the end.
An example is a whiteside SC55 engraving bit but with a 45Deg point on the end.