Search found 12 matches
- Mon Apr 26, 2021 10:43 pm
- Forum: VCarve - Gallery
- Topic: Another Resin Filled Tray
- Replies: 7
- Views: 3511
Re: Another Resin Filled Tray
Really like this. Well done! Have three friends with a bicycling history that would find this a wonderful gift.
- Sun Nov 29, 2020 4:51 pm
- Forum: VCarve - Gallery
- Topic: Frontispiece
- Replies: 7
- Views: 2565
Re: Frontispiece
That is AWESOME! I can well imagine the time that went into editing.
- Sun Nov 29, 2020 4:44 pm
- Forum: VCarve - Gallery
- Topic: "The Eye of Zank"
- Replies: 8
- Views: 2627
Re: "The Eye of Zank"
Nicely done Egyptian mythology symbol - the right eye of Horus.
Have a question ... I am planning some carvings in walnut slabs. What, if any, issues have you run into carving in the cookies?
Spindle
Have a question ... I am planning some carvings in walnut slabs. What, if any, issues have you run into carving in the cookies?
Spindle
- Sun Nov 29, 2020 4:38 pm
- Forum: VCarve - Gallery
- Topic: Zank Inlay wine service
- Replies: 10
- Views: 3133
Re: Zank Inlay wine service
Beautifully done inlay!!!
- Sat Nov 28, 2020 3:00 pm
- Forum: VCarve - Gallery
- Topic: Butterfly Box
- Replies: 10
- Views: 2631
Re: Butterfly Box
Jay,
Not your attention - didn't have location in my profile until later yesterday. Yes, we are close. Looks like Scott T is a WI native also.
Not your attention - didn't have location in my profile until later yesterday. Yes, we are close. Looks like Scott T is a WI native also.
- Sat Nov 28, 2020 1:10 am
- Forum: VCarve - Gallery
- Topic: Butterfly Box
- Replies: 10
- Views: 2631
Re: Butterfly Box
Gkas and Scot,
Thanks for the compliments on the box. Bought some small sample sheets of the copper veneer from veneersupplies.com. Cut one sheet into strips for inlay in another box.
Thanks for the compliments on the box. Bought some small sample sheets of the copper veneer from veneersupplies.com. Cut one sheet into strips for inlay in another box.
- Sat Nov 28, 2020 1:00 am
- Forum: VCarve - Gallery
- Topic: Butterfly Box
- Replies: 10
- Views: 2631
Re: Butterfly Box
Thanks Jay. Appreciate your comments. I wasn't sure I could cut the copper veneer with the CNC, but it worked.
- Fri Nov 27, 2020 6:27 pm
- Forum: VCarve - Gallery
- Topic: Butterfly Box
- Replies: 10
- Views: 2631
Re: Butterfly Box
Thanks Steve. It turned out better than I expected. The copper veneer really stood out nicely.
- Fri Nov 27, 2020 5:09 pm
- Forum: VCarve - Gallery
- Topic: Butterfly Box
- Replies: 10
- Views: 2631
Butterfly Box
Wood is flame birch. CNC routed butterfly shape then colored black. Cut the copper inlay pieces sandwiched between two layers of thin ply. After copper pieces were glued in, filled with clear epoxy. Sides were routed butterfly outline, inlayed with black wire then filled with clear epoxy. The black ...
- Tue Nov 26, 2019 6:10 pm
- Forum: VCarve - General
- Topic: VCarve Inlay clean-up
- Replies: 5
- Views: 2262
Re: VCarve Inlay clean-up
Thank all for your advice - makes total sense. No drum sander, so the cut and hand or rotary sand and/or scraper will do it.
Thank you again, it is immensely helpful to have experienced folks to learn from.
Thank you again, it is immensely helpful to have experienced folks to learn from.
- Fri Nov 08, 2019 7:46 pm
- Forum: VCarve - General
- Topic: VCarve Inlay clean-up
- Replies: 5
- Views: 2262
VCarve Inlay clean-up
New to this. Have a question. Could I run a V-carve inlay through a very light pass on my planer after bandsawing off the majority of the inlay wood? I worry it may chip out tight corners of the inlay.
- Wed Nov 06, 2019 2:35 am
- Forum: VCarve - Tips and Tricks
- Topic: Avoiding Machine Gotchya's
- Replies: 48
- Views: 200879
Re: Avoiding Machine Gotchya's
I am new at this, but one thing I found that caused depth problems across even a small piece of wood, is when clamps were unevenly spaced around the perimeter. This caused the unclamped area to be slightly higher which caused uneven depth across the carvings.
VCarve Desktop
VCarve Desktop