Search found 10 matches
- Mon Dec 16, 2019 11:45 pm
- Forum: Gadgets - Requests
- Topic: Gadgets
- Replies: 2
- Views: 7332
Re: Gadgets
Thank you. When I saw “gadget requests” I assumed this was the place. I shall ask “support”... happy holidays!
- Sat Dec 14, 2019 12:45 am
- Forum: Gadgets - Requests
- Topic: Gadgets
- Replies: 2
- Views: 7332
Gadgets
Hello and thanks for such wonderful software.
At work, I get to play with Aspire and love the box maker gadget. At home I have Vcarve desktop. Do you plan on making any gadgets available for desktop?
Jeff
At work, I get to play with Aspire and love the box maker gadget. At home I have Vcarve desktop. Do you plan on making any gadgets available for desktop?
Jeff
- Thu Dec 12, 2019 12:50 am
- Forum: VCarve - Tips and Tricks
- Topic: Clipart
- Replies: 16
- Views: 6314
Re: Clipart
Hello, I use an airbrush for accuracy. I seal the item first, then put a layer of liquid mask around the painted area. After painting, I remove the mask do a very light sanding and the apply finish. Some of my products won’t handle the usual “paint everything then sand off what you don’t want” so my...
- Tue Mar 19, 2019 2:22 am
- Forum: Post Processors
- Topic: Adjust depth of V cut
- Replies: 6
- Views: 9122
Re: Adjust depth of V cut
Well, since I couldn't find an answer here, I did a little experimenting. Here's what I found..... None of the tutorial videos from Vectric really address the problem. As was mentioned, various angles, induces hyperbol caused by the refraction of light on the rays of the moon and other such mumbo ju...
- Mon Mar 18, 2019 8:31 pm
- Forum: VCarve - General
- Topic: Depth of V carve letters
- Replies: 5
- Views: 3197
Depth of V carve letters
Hello all, Is there a way to limit the depth of cut when V carving letters? I am attempting to cut names into a 1/4" piece of wood. I pocket a .2" deep pocket for the glass to fit in, then I attempt to V carve a name into the bottom of the pocket. Whether I use a 60' or a 90' V carve bit, it either ...
- Mon Mar 18, 2019 4:45 pm
- Forum: Post Processors
- Topic: Adjust depth of V cut
- Replies: 6
- Views: 9122
Adjust depth of V cut
Hello all, I am attempting to cut a pattern onto a piece of 1/4" wood using V carved letters. The problem is, the bit goes much too deep and cuts through the wood. I also use 1/8 wood with the same problem. This is the case whether I use a 60' V bit or the 90' v bit. In Vectric Pro/Desktop/Aspire, i...
- Thu Mar 14, 2019 6:55 pm
- Forum: Aspire - General
- Topic: Depth of V carve letters
- Replies: 4
- Views: 2370
Depth of V carve letters
Hello all, I am attempting to make some small signs, 3 1/2" diameter. If I use the 60' Vee bit, the letters are too small and the bit chops the letters apart. How do I make the bit cut to a shallower depth? Do I have to go to a small bit, like a 1/8" engraving bit (even though I am not engraving the...
- Tue Mar 05, 2019 9:14 pm
- Forum: VCarve - General
- Topic: Downloading 3D tabs
- Replies: 3
- Views: 2780
Downloading 3D tabs
Hello all, When I attempt to download some of the "downloadable" tabs in Vcarve Desktop, it says I am not "signed in". So, I sign in and it says I am successfully linked. Then when I go back and try to download the tab again, I get the same message. How do I get out of this loop and download the res...
- Sun Mar 03, 2019 12:56 am
- Forum: Hardware related questions
- Topic: Next Wave Automation touch plate with Shapeoko
- Replies: 1
- Views: 2402
Next Wave Automation touch plate with Shapeoko
Hello all, I understand this is the Vectric forum but am hoping someone might read this and supply an answer. I have also posted to the Carbide forum site..... I recently acquired a Next Wave Automation touch plate that I hope to use with my Shapeoko XXL. I haven't built the machine yet (still worki...
- Mon Feb 11, 2019 4:38 pm
- Forum: Aspire - General
- Topic: Tutorial Videos
- Replies: 2
- Views: 1500
Tutorial Videos
Hello all...… I am very new at using the Aspire software and find that the video tutorials are very helpful. However, as they are posted on YouTube, they do tend to jump around a bit. My question is: is there anywhere that lists them from 1 to ? in some sort of chronological order? It would be nice ...