Search found 12 matches
- Mon Mar 18, 2019 2:09 pm
- Forum: VCarve - General
- Topic: Bad poplar board
- Replies: 37
- Views: 12408
Re: Bad poplar board
Poplar is my go to wood for photoVcarve, but the max depth is 0.08” with a ball nose bit, and I pick the whitest boards I can find and stay away from the ones with too much green in them. For vCarving and 3D work it does get a little to stringy but I have never seen one that bad.
- Sat Dec 22, 2018 3:10 pm
- Forum: VCarve - General
- Topic: Burl advice needed
- Replies: 32
- Views: 9950
Re: Burl advice needed
The wood Turning market in the northeast is on fire I would try a wood Turning forum to get top dollar for those burls, if I was closer the truck would be heading north right now. A bowl I could sell for 50 bucks down here easily sells for 100-150 up there. Vases and Clocks, and Bowls and Platters o...
- Wed Dec 05, 2018 2:06 pm
- Forum: VCarve - General
- Topic: Laser
- Replies: 6
- Views: 4774
Re: Laser
I have the 4.2w J-tech and for what I use it for it is great, but its driver is not variable power so I can’t burn grey scale images with it. They do have a 2.5w variable power laser that does really good work on pictures. When I looked at the shark before I got my axiom if I remember correctly the ...
- Thu Nov 08, 2018 2:47 pm
- Forum: VCarve - General
- Topic: Laser in Tool Database
- Replies: 9
- Views: 6944
Re: Laser in Tool Database
Vectric mentioned a laser module “coming soon” so I guess that is what it is for. I have mine set up as an end mill currently and it work fine with the quick engrave toolpath. I am eagerly awaiting the release of the laser module to see what functionality it adds.
- Mon Sep 03, 2018 6:53 pm
- Forum: VCarve - General
- Topic: Customer Proofing
- Replies: 3
- Views: 2506
Re: Customer Proofing
After you preview the toolpath there is a button to save preview image can be jpeg our other format you want.
- Fri Aug 10, 2018 2:08 am
- Forum: PhotoVCarve - General
- Topic: Learning PVC.. How am I doing?
- Replies: 19
- Views: 14274
Re: Learning PVC.. How am I doing?
Being a PVC novice myself I have been experimenting lately, here a a few I did this week. I use a 0.0313 tapered ball nose bit I just put it in the tool dB as a ball nose since at the depth I’m cutting the taper won’t matter. Max carving depth is 0.08” with 10% - 20% line spacing and a 45 degree lin...
- Sun Jun 24, 2018 2:38 pm
- Forum: VCarve - General
- Topic: Confusing Error
- Replies: 10
- Views: 3970
Re: Confusing Error
been away from the computer for a while sorry for the delay. When I go to Selection>Select All Open Vectors the popup says no open vectors found. When I go to create the Quick Engrave (Fill) toolpath the popup says 4 open vectors found and are being ignored. I have been trying to upload the file as ...
- Tue Jun 19, 2018 12:24 pm
- Forum: VCarve - General
- Topic: Confusing Error
- Replies: 10
- Views: 3970
Confusing Error
I have a file that when I go to create the toolpath it says there are 4 open vectors that are being ignored, but when I go to the menu bar and “select, all open vectors” it says there are no open vectors found. Visually I cannot find any open vectors, is there another way for the software to show me...
- Sun May 20, 2018 12:08 am
- Forum: VCarve - General
- Topic: Time estimate ?
- Replies: 7
- Views: 3561
Re: Time estimate ?
Reduced the scale to 1 but unless I triple the feed rate for the bit the time estimate is grossly overestimated. Ex. Finish 3D pass that was done in 6 hours was estimated at 23hr 45m only way to get the software to get a close estimate was to triple the feed rate from 30inches/min to 90 Is the time ...
- Fri May 18, 2018 4:51 pm
- Forum: VCarve - General
- Topic: Time estimate ?
- Replies: 7
- Views: 3561
Time estimate ?
When finishing up a design after doing the toolpaths I look at the time estimate and it says 27 hours or so but when I cut it it is done in 2-3 hours. I have checked all the feedrates on the bits and looked at the rapid rates but I am at a loss as to why the software overestimates so badly. Anyone h...
- Sat Apr 28, 2018 9:18 pm
- Forum: PhotoVCarve - General
- Topic: Looking for tool advise
- Replies: 1
- Views: 2850
Looking for tool advise
Got into my first project and realized I don’t have many bits since I just got a starter set with my CNC. My best result was with a 30* 0.25 vbit but I feel like I should be able to get better definition. What are some of your favorite bits to use with PVC before I run off to Amazon and fill my cart...
- Wed Apr 11, 2018 6:40 pm
- Forum: Cut2D - General
- Topic: The New Map Thread - Show us where you are in the world
- Replies: 1439
- Views: 4382906
Re: The New Map Thread - Show us where you are in the world
Eclectic, Al 36024