Search found 397 matches

by cusoak
Thu Jul 23, 2020 2:18 pm
Forum: VCarve - General
Topic: 10.5 Clipart
Replies: 0
Views: 188

10.5 Clipart

Now that I have 10.5 I have a question is there anything new in the clipart section that might be different than it was in version 10.0
Thanks Jeff
by cusoak
Wed Jul 22, 2020 1:07 pm
Forum: VCarve - General
Topic: G code Error message
Replies: 18
Views: 618

Re: G code Error message

This was only a test suggested by someone who posted here .
I design in inches and cut in inches only I have never use MM for anything.
now that I have inch shapeoko PP that works all is good.
Thanks everyone.
Jeff
by cusoak
Wed Jul 22, 2020 12:57 pm
Forum: VCarve - General
Topic: G code Error message
Replies: 18
Views: 618

Re: G code Error message

I did a designed in inches then save to cut files one in inches and the other in MM. Did not reset the design to MM
Jeff
by cusoak
Tue Jul 21, 2020 3:11 pm
Forum: VCarve - General
Topic: G code Error message
Replies: 18
Views: 618

Re: G code Error message

Today I got a new shapeoko pp in inches from vectric and installed it in 10.5 I did 1 file and saved the gcode in inches and then I saved the same gcode file in MM The inch one cut perfect. The mm one started and made one pass with out cutting any thing then plunged down and cut but did not cut the ...
by cusoak
Mon Jul 20, 2020 11:22 am
Forum: VCarve - General
Topic: G code Error message
Replies: 18
Views: 618

Re: G code Error message

Hooby so do you design in10.5 using MM and use the shapeoko mm gcode to run your cut files.
Or can you design in inches and still use the MM gcode.
Jeff
by cusoak
Sun Jul 19, 2020 2:44 pm
Forum: VCarve - General
Topic: G code Error message
Replies: 18
Views: 618

Re: G code Error message

well I up dated to the new version 10.505 and got an error message and was not able to run the cut program.
So do I go to vcp10.0 and select that pp and copy it to 10.5 is it that simple or do I have to do something else.
Jeff
by cusoak
Sun Jul 19, 2020 1:32 pm
Forum: VCarve - General
Topic: G code Error message
Replies: 18
Views: 618

Re: G code Error message

I have not up dated to the latest version but I am doing that today.
then I will retry the file with new updated cut files and see what happens
Jeff
by cusoak
Sat Jul 18, 2020 2:50 pm
Forum: VCarve - General
Topic: G code Error message
Replies: 18
Views: 618

Re: G code Error message

when I open a new 10.5 file there is a box that comes up and want me to migrate things from 9.5 to 10.5 tne post processor is on that screen.But I am pretty sure I did that then I down loaded 10.5 should I do it that way.
jeff
by cusoak
Sat Jul 18, 2020 12:27 pm
Forum: VCarve - General
Topic: G code Error message
Replies: 18
Views: 618

Re: G code Error message

Well I created the file in vc10.5 and used the the same post processor.that was in 10.0. I did not do anything to get it It was just there in the save toolpath section.Shapeoko(inch).(*gcode) If I need to copy the one from 10.0 to 10.5 I am going need some instructions on how to do that. Also I have...
by cusoak
Fri Jul 17, 2020 2:56 pm
Forum: VCarve - General
Topic: G code Error message
Replies: 18
Views: 618

Re: G code Error message

Is the Error message a function of a problem in the design or in the controller software.
jeff
by cusoak
Fri Jul 17, 2020 2:06 pm
Forum: VCarve - General
Topic: G code Error message
Replies: 18
Views: 618

G code Error message

First time G Code Error message.
I created ca file in the new version vcp10.5 And when i opened Carbide Motion my controller software I got the 2 attached error messages.
Is the problem that caused this Error in VCP or Carbide motion.
Jeff
by cusoak
Fri Jul 17, 2020 1:16 pm
Forum: VCarve - General
Topic: Poly Line does not show in vcp10.5
Replies: 3
Views: 219

Re: Poly Line does not show in vcp10.5

That was what I was doing. Thanks.
Jeff
by cusoak
Thu Jul 16, 2020 2:28 pm
Forum: VCarve - General
Topic: Recently open files
Replies: 1
Views: 128

Recently open files

when you first open a new session on vcp there is a list of Recently open file listed .Could someone tell me how to remove them from that screen.please.
Thanks Jeff
by cusoak
Thu Jul 16, 2020 2:06 pm
Forum: VCarve - General
Topic: Poly Line does not show in vcp10.5
Replies: 3
Views: 219

Poly Line does not show in vcp10.5

I am running the 10.5 version vcarve pro. I was using the poly line tool and see that I click and drag the line to another point it does not show as I drag it .It does not show up until I click the end point. Is there something I need to turn on to see it being created. It shows when I go back and u...
by cusoak
Tue Jul 07, 2020 12:54 pm
Forum: Aspire - General
Topic: 10.5 is COMING SOON - Watch this space
Replies: 88
Views: 7657

Re: 10.5 is COMING SOON - Watch this space

I see that vcarve pro10.5 is ready to .When I click on it in the soft ware it takes my to myvectric account .So I need to download it just like I did vcarve pro10 when I paid to upgrade to 10?
Jeff