Search found 30 matches
- Fri Jun 04, 2021 1:33 am
- Forum: Aspire - General
- Topic: Unable to upgrade to 10.5
- Replies: 4
- Views: 1577
Re: Unable to upgrade to 10.5
Yep, that is what it was. Thank you
- Sat May 22, 2021 1:35 pm
- Forum: Aspire - General
- Topic: Unable to upgrade to 10.5
- Replies: 4
- Views: 1577
Unable to upgrade to 10.5
When I log into my account and try to upgrade, the portal takes me to this page that will not load. https://portal.vectric.com/upgradeEligibility
is this page not working or is it on my end?
is this page not working or is it on my end?
- Sat Jun 08, 2019 10:06 pm
- Forum: Aspire - General
- Topic: Laser support being added?
- Replies: 1
- Views: 1229
Laser support being added?
I was reading the manual yesterday, yea I know why would you read a manual, but this time I saw a section on laser support and that it was being beta tested. Does anyone know when this could be available and is it to late to be a beta tester? Sadly none of these things were in the manual. Thanks
- Sun Jun 02, 2019 11:26 pm
- Forum: Aspire - General
- Topic: Question about uccnc and laser
- Replies: 3
- Views: 2087
Re: Question about uccnc and laser
Ah Thanks. I missed that in the setup about the i/o pin. And I guess I will dig in and see if I can figure out how to do a custom Post Processor. Over all I really like UCCNC so far. Thanks again
- Sun Jun 02, 2019 9:31 pm
- Forum: Aspire - General
- Topic: Question about uccnc and laser
- Replies: 3
- Views: 2087
Question about uccnc and laser
capture_001_02062019_162923.jpg Hello everyone. I stopped using Mach3 today and installed my new uc300eth-5ltp and UCCNC. Everything is working great on the router part but when I put my laser on the machine and try to engrave something the laser fires as soon as the g code starts. I have tried sev...
- Thu May 09, 2019 2:20 pm
- Forum: Hardware related questions
- Topic: endurance laser
- Replies: 10
- Views: 5129
Re: endurance laser
So as I understand it Mach3 is to slow to run pic engrave to engrave photos per pic engraves web site. Is there any alternative to mach 3 that will work with an ess and a c10 breakout board that is fast enough? Should I switch to uccnc and get a new control board? I saw pic engrave has a board you c...
- Sat May 04, 2019 10:55 pm
- Forum: Hardware related questions
- Topic: endurance laser
- Replies: 10
- Views: 5129
Re: endurance laser
So many check boxes...... lol Thank you for you help!!!
- Sat May 04, 2019 4:04 pm
- Forum: Hardware related questions
- Topic: endurance laser
- Replies: 10
- Views: 5129
Re: endurance laser
Ok so I had a semi bad C10 board which has been fixed. So now I am able to use my m3 and m2 commands to turn the laser on and off with but I need to be able to use my m11 and m10 commands but I am unable to get this to work. Do I put the output number that I used in the outputs tab of the ports and ...
- Sat May 04, 2019 3:19 pm
- Forum: Hardware related questions
- Topic: endurance laser
- Replies: 10
- Views: 5129
Re: endurance laser
Thanks Mobius. I was in a rush yesterday and on my phone with bad service so I couldn't be more specific. I am trying to get my lase with work with PWM signals from mach3. I know my TTL input on my laser box is good because when I put my laser in TTL mode and use a 1.5 volt battery on the TTL wires ...
- Fri May 03, 2019 5:55 pm
- Forum: Hardware related questions
- Topic: endurance laser
- Replies: 10
- Views: 5129
endurance laser
Does anyone have any first had experience with the endurance laser and or endurance laser control box? My new laser showed up and I am having some difficulty getting it to work correctly. I am sure it's my fault but would like a second opinion. I have tried the face book support group for the brand ...
- Sat Apr 06, 2019 12:47 pm
- Forum: VCarve - Gallery
- Topic: 2 Heart Stands...River Red Gum and Ebony
- Replies: 25
- Views: 10160
Re: 2 Heart Stands...River Red Gum and Ebony
Wow Scott your work is AWESOME! My wife Jaime saw it and she loved it as well!
- Sat Mar 16, 2019 1:55 am
- Forum: Aspire - General
- Topic: Engrave Stainless Yeti
- Replies: 7
- Views: 3652
Re: Engrave Stainless Yeti
yes, I built a 4x4 Joe's cnc. But can't really say it was that hard, Joe's forum and kit made it as easy as a model car to put together well minus the welded base and wiring. I will try and chat with George tomorrow and ask if anyone has tested his laser on powder coating.
- Sat Mar 16, 2019 12:48 am
- Forum: Aspire - General
- Topic: Engrave Stainless Yeti
- Replies: 7
- Views: 3652
Re: Engrave Stainless Yeti
I have considered a laser many times lol. Just trying to make due with the considerable investment I have in CNC router equipment but just from the searches I have done seems like it's not practical to do what I want with just a cnc router. I have been considering an endurance laser add on http://en...
- Fri Mar 15, 2019 9:23 pm
- Forum: Aspire - General
- Topic: Engrave Stainless Yeti
- Replies: 7
- Views: 3652
Engrave Stainless Yeti
For years I have sandblasted mugs ( non coated ) and then a few years ago my best customer gave me two cases of powder coated mugs to do, wow what an adventure, my production time went from 5 min. a mug to 45 min a mug because that powder coat is hard as a coffin nail! I have to increase my mask thi...
- Fri Mar 15, 2019 8:53 pm
- Forum: Aspire - General
- Topic: Can this be done?
- Replies: 11
- Views: 4042
Re: Can this be done?
Just wanted to say thank you for posting a link to G code ripper! wow can't believe its free but glad it is!