Search found 70 matches
- Fri May 15, 2020 5:23 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
Problem solved. With a lot of help from member BillK we figured the the machine soft limits were probably to blame. I still don't know exactly why it wasn't working as my Z was set to 250mm or almost 10" of travel and I only needed about 4" I changed the Z setting to 300mm and it worked. I don't see...
- Thu May 14, 2020 1:56 am
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
Anyway you can send me the tap file? I’ll take a look at the code. Send me a PM and I’ll give you my email. One other thought: reset the jig to a different spot on your table, a couple of inches in X, a couple in Y. Just to see if its the machine in that spot. You can probably just run an air cut b...
- Wed May 13, 2020 11:17 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
So I just ran this again and changed the gap above material to 2.25 inches and safe Z to .4" which is a ton of extra room and the problem is the same. It mills out EXACTLY the same I thought it would be fine or less or even more but it is exactly the same. I don't know what else to try.
- Wed May 13, 2020 11:15 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
If the preview looks correct then the problem is most l;ikely else where, can't help with code as I don't read it although I really should learn :oops: :oops: your not hitting the top stop on your z axis are you? That would affect your set z axis zero position, also check for binding towards the to...
- Wed May 13, 2020 9:42 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
I just looked at it and saw the same thing you did. I think the values are +/- mm's for the movement of the Z. At least that is what it looks like to me
- Wed May 13, 2020 9:24 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
The Laguna IQ uses a Hand Held Controller. I have never looked in the the code for it
- Wed May 13, 2020 8:02 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
- Wed May 13, 2020 7:49 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
Okay this may sound like a silly/crazy question --- Why are you changing the SAFE Z from Side one (TOP) to side two (BOTTOM)??? Even the Home position Z Changes from TOP to BOTTOM!!! Isn't the material in a fixture at a fixed position? Sharkcutup Yes Material is in a fixture. The software is doing ...
- Wed May 13, 2020 7:13 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
With my bit in the chuck and the Z at its limit I have the following measurements From the Bit to the Bed 4.75" Gap From the Bit to the Bottom of Material 4.03" Gap From the Bit to the Top of Material 2.25" Gap So if I set a gap of 2 inches about my material I should not be maxing out my Z travel. T...
- Wed May 13, 2020 6:56 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
Go to the Shark forum. There are a lot of posts on it there. One that I saw says on the pawn the Z clearance is set too high, I think 1.86, on the second side file that you are having trouble with. Since that is close to the clearance you say you have, you may be exceeding the Z travel and losing t...
- Wed May 13, 2020 3:44 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
Any Thoughts?? I am at a complete loss
- Tue May 12, 2020 6:42 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
The preview looks correct. The thing I find strange is that it cuts it in a straight line, It isn't even cutting it at a arc at the wrong height it just tops out and then goes straight across. Is there a max Z setting that I am missing?
- Tue May 12, 2020 5:59 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
The preview looks correct. The thing I find strange is that it cuts it in a straight line, It isn't even cutting it at a arc at the wrong height it just tops out and then goes straight across. Is there a max Z setting that I am missing?
- Tue May 12, 2020 4:04 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
I received the drawing for my bit and the only difference is that the default bit in the .crv is 5deg taper and my bit is 3.5deg taper. I will make the adjustment but not sure that is the issue.
- Tue May 12, 2020 3:35 pm
- Forum: VCarve - General
- Topic: Problem with 3D cut job
- Replies: 26
- Views: 6153
Re: Problem with 3D cut job
This is the second piece I tried to cut out and the first one had the same results. The first one was at a thickness of 1.75 and I did not adjust the material size in the software and thought that, that was my issue. For the one posted above the material thickness is exactly 1.78 as I thought that w...