I have the same problem! I will be trying to save a file and it just locks up and I have to start all over again.
Don't know why this is happening. Never did it with version 10.0
Search found 87 matches
- Mon Nov 23, 2020 2:01 am
- Forum: VCarve - General
- Topic: V-Carve hangs sometimes
- Replies: 2
- Views: 1042
- Tue Oct 13, 2020 12:11 am
- Forum: VCarve - General
- Topic: out of soft
- Replies: 5
- Views: 1901
Re: out of soft
Out of soft limit means that the project you're cutting is greater than the machine can cut.
Check to make sure that the project isn't bigger than the spindle can move to.
Check to make sure that the project isn't bigger than the spindle can move to.
- Sat Sep 12, 2020 5:05 am
- Forum: VCarve - General
- Topic: Hoping to use 1/2"-shank bits
- Replies: 9
- Views: 2858
Re: Hoping to use 1/2"-shank bits
I don't think any palm router can handle a 1/2" collet. I have 2 palm routers and have only used 1/4" bits in either of them.
- Sat Sep 12, 2020 5:03 am
- Forum: VCarve - General
- Topic: Lack of user manual
- Replies: 15
- Views: 4132
Re: Lack of user manual
Just wondering how you paid $1500 for V Carve Pro? Vectric has so many help videos, and the help section while using the software probably answers 90% of any question you could possibly ask. Just my 2 cents, but you sound pissed! This forum has so many members that can answer any possible question y...
- Wed Sep 09, 2020 3:21 am
- Forum: VCarve - General
- Topic: Sharpening Ball-nose
- Replies: 32
- Views: 6815
Re: Sharpening Ball-nose
Who is IIRC please?
- Thu Sep 03, 2020 5:30 pm
- Forum: VCarve - General
- Topic: Glass Door Groove for Rubber Mold
- Replies: 2
- Views: 1127
Re: Glass Door Groove for Rubber Mold
I would either use the table saw or router table to cut that slot. It would be much faster and requires minimal setup!
- Tue Aug 11, 2020 11:41 pm
- Forum: VCarve - General
- Topic: double sided Project
- Replies: 5
- Views: 1714
Re: double sided Project
I have personally found that even though I have the project piece cut perfect and copy my image to the other side and then just flip the piece, the cut still comes out off somewhat unless I use the dowel method. When I use that, I can make as many pieces as I want and they all come out spot on. I do...
- Thu Jul 23, 2020 4:36 pm
- Forum: VCarve - General
- Topic: Do not update to a new post-processor if you had one that works!!
- Replies: 25
- Views: 6369
Re: Do not update to a new post-processor if you had one that works!!
When upgrading from 10.0 to 10.5, is there a prompt asking if you want to upgrade your post processor?
If not, how would I keep the current PP and not use the upgraded one?
My machine is working just fine with the processor I have been using since ver 8.5!
If not, how would I keep the current PP and not use the upgraded one?
My machine is working just fine with the processor I have been using since ver 8.5!
- Fri May 22, 2020 3:40 pm
- Forum: VCarve - General
- Topic: Y-axis Soft Limit Error
- Replies: 4
- Views: 4462
Re: Y-axis Soft Limit Error
This message: Y-axis soft limit error is saying the you are trying to cut further than the Y axis can actually travel and the spindle or router can't move that far. As an example, if your Y travel is 24" and you are trying to cut 26".
- Sat Apr 18, 2020 3:28 pm
- Forum: VCarve - General
- Topic: Viewing a project
- Replies: 6
- Views: 1784
Re: Viewing a project
Thanks for the tip. I recreated the project and deleted the old project, but will remember that tip if it ever happens again. It wasn't a hard project and only took 15 min to recreate.
- Sat Apr 18, 2020 3:54 am
- Forum: VCarve - General
- Topic: Viewing a project
- Replies: 6
- Views: 1784
Re: Viewing a project
No It's all in inches. I really don't know what happened to the file! All I know is when I open it, it's super small until I zoom in on it.
The file cuts fine, I just have to zoom in.
I checked several of my other projects and none of them act this way. Just this one.
The file cuts fine, I just have to zoom in.
I checked several of my other projects and none of them act this way. Just this one.
- Fri Apr 17, 2020 11:35 pm
- Forum: VCarve - General
- Topic: Viewing a project
- Replies: 6
- Views: 1784
Viewing a project
I have Version 10.021 and when I open a project, it is super small and I have to zoom in on it to actually see the project.
I don't know what i did, but it's not on all my projects, just a few.
How can I avoid this?
I don't know what i did, but it's not on all my projects, just a few.
How can I avoid this?
- Thu Apr 16, 2020 11:21 pm
- Forum: VCarve - General
- Topic: Laser cutting
- Replies: 9
- Views: 2757
Re: Laser cutting
I don't have a laser, but the size of your laser is for engraving only. I can't cut 1/4" of anything. From what I understand, you would need at least a 40 watt or even 60 watt laser to actually cut anything that thick. I have thought about getting one for my CNC, but I know I will need something mor...
- Thu Apr 02, 2020 6:33 pm
- Forum: VCarve - General
- Topic: Adding the degree symbol when typing text
- Replies: 9
- Views: 2892
Re: Adding the degree symbol when typing text
I don't have a keypad on this laptop, but I am using the keypad function and it works with Times New Roman font, but no a single line font.
Thanks for all the help form everyone!
Thanks for all the help form everyone!
- Thu Apr 02, 2020 4:22 pm
- Forum: VCarve - General
- Topic: Adding the degree symbol when typing text
- Replies: 9
- Views: 2892
Re: Adding the degree symbol when typing text
Sorry guys, but holding the ALT key and typing 248 does nothing.
I tries truetype fonts and single line fonts
Helvetica as a single line and Times New Roman as a true type
I tries truetype fonts and single line fonts
Helvetica as a single line and Times New Roman as a true type