Search found 8 matches
- Fri Mar 17, 2023 5:37 pm
- Forum: VCarve - General
- Topic: VCarve Pro & Desktop 11.5 are OUT NOW!
- Replies: 45
- Views: 28594
Re: VCarve Pro & Desktop 11.5 are OUT NOW!
I just upgraded to 11.504, and I have a Shopbot PRSAlpha 96x48 ATC (automatic tool changer). The software will not allow me to save a file with more than a single toolpath. What am I missing?
- Wed Dec 04, 2019 4:11 pm
- Forum: VCarve - Tips and Tricks
- Topic: Wood warping after carving
- Replies: 10
- Views: 8447
Re: Wood warping after carving
Wow. Thanks for the helpful suggestions! As you can tell, I'm a little out of my element here. I'll now look into how to determine old growth from rapid growth. The three pieces that are glued together were all from one (roughly 12' long) board. Also, noted on the direction-of-grain suggestion. In t...
- Tue Dec 03, 2019 11:07 pm
- Forum: VCarve - Tips and Tricks
- Topic: Wood warping after carving
- Replies: 10
- Views: 8447
Re: Wood warping after carving
I thought I uploaded images. Not sure what happened.
- Tue Dec 03, 2019 11:02 pm
- Forum: VCarve - Tips and Tricks
- Topic: Wood warping after carving
- Replies: 10
- Views: 8447
Wood warping after carving
Hi everyone. I purchased a 3D model of a Byzantine cross for carving. I've carved it once before, out of Mahogany, and it came out great. This time, I carved it out of cherry. I glued up three strips of cherry wood that were approximately 8" x 36", giving me a blank of 24" x 36". I ended up carving ...
- Tue Jul 30, 2019 3:35 pm
- Forum: Cut2D - General
- Topic: The New Map Thread - Show us where you are in the world
- Replies: 1438
- Views: 4378291
Re: The New Map Thread - Show us where you are in the world
Experia USA
2880 McEver Road
Buford, GA 30518
2880 McEver Road
Buford, GA 30518
- Wed Aug 30, 2017 9:10 pm
- Forum: VCarve - General
- Topic: 3D Carving - Roughing boundary?
- Replies: 4
- Views: 2507
Re: 3D Carving - Roughing boundary?
Now that the finishing toolpath is 2/3 done, I think I know what it is. Around the edge is a small upward-sloping ridge, right near the edge. I could not discern it in the model, but can see/feel in in the finished part. Now, my concern is whether or not it will break off when I do it in wood. In th...
- Wed Aug 30, 2017 5:52 pm
- Forum: VCarve - General
- Topic: 3D Carving - Roughing boundary?
- Replies: 4
- Views: 2507
Re: 3D Carving - Roughing boundary?
I am using a 1/4" bit for roughing, and originally I had a 0.2" boundary offset. I thought that might be it, so then I re-calculated the roughing toolpath with a 0.135 offset. No difference.
I then tried it with 0.00 boundary offset, with no difference.
I then tried it with 0.00 boundary offset, with no difference.
- Wed Aug 30, 2017 4:41 pm
- Forum: VCarve - General
- Topic: 3D Carving - Roughing boundary?
- Replies: 4
- Views: 2507
3D Carving - Roughing boundary?
I everyone. I'm new to 3D work, so please bear with me. I do not understand why the roughing toolpath is doing what it is doing. I am wanting to carve an Orthodox cross, and the roughing toolpath leaves approximately .125 of a border on the outer edge of the model (see image). That leaves a lot of m...