Search found 53 matches

by myshadowboxes
Sat Mar 21, 2015 11:46 pm
Forum: Aspire - Gallery
Topic: Faux Wood Slab K-Cup Holder
Replies: 12
Views: 4298

Re: Faux Wood Slab K-Cup Holder

Thank you sir... And now it is a little better because of you. I wish the cabinets started a little higher so I could put my Coffee sign up, but for now it sits behind the K-cup holder which really doesn't get used as much as the machine on the left... now that's coffee. I think I over did the paint...
by myshadowboxes
Sat Mar 21, 2015 10:03 pm
Forum: Aspire - Gallery
Topic: Faux Wood Slab K-Cup Holder
Replies: 12
Views: 4298

Re: Faux Wood Slab K-Cup Holder

Now to complete the pictures...

K-Cup holder in it's home
by myshadowboxes
Sun Feb 08, 2015 11:41 pm
Forum: Aspire - Gallery
Topic: Faux Wood Slab K-Cup Holder
Replies: 12
Views: 4298

Faux Wood Slab K-Cup Holder

Michael Tyler has done it again, another great project. This one was a lot of fun to do... I would never say I was a painter, but Michael has me out trying it again. I might just go back and do some more of the ones I skipped... Thanks again Vectric and Michael Blanks.png Cut Out.jpg Finished K Cup....
by myshadowboxes
Mon Jan 28, 2013 3:33 am
Forum: Aspire - Gallery
Topic: The Fox and the Stork
Replies: 24
Views: 10156

Re: The Fox and the Stork

Beautiful as always Michael!!!! You do amazing work...
by myshadowboxes
Fri Oct 14, 2011 2:15 pm
Forum: Design & Carve - Aspire
Topic: Horse Carriage Sign
Replies: 5
Views: 5487

Re: Horse Carriage Sign

The palm trees came from the first Aspire disk I think...i am at work and can't check. The carriage came from the western disk...i really wish I had more time to do more.
by myshadowboxes
Thu Oct 13, 2011 2:21 am
Forum: Design & Carve - Aspire
Topic: Horse Carriage Sign
Replies: 5
Views: 5487

Horse Carriage Sign

Well here is my first western scene design. I actually did the palm tree first using the same design as the welcome sign. Ended up doing the Western Horse Carriage sign for my grandfather. One thing I will point out on the "Honeycutt" sign and it is hard to see here because I did try to fix it. If y...
by myshadowboxes
Tue Jun 14, 2011 2:40 am
Forum: Aspire - Gallery
Topic: Wedding Cake Base
Replies: 2
Views: 1331

Wedding Cake Base

A Wedding Cake Base made for a friend of ours using Aspire and my Camaster
by myshadowboxes
Wed May 25, 2011 10:13 pm
Forum: Aspire - General
Topic: Can someone give me a quote on making this a 3d file
Replies: 2
Views: 944

Can someone give me a quote on making this a 3d file

Not sure if this is the right place for this or not, but I am looking for a quote on making the attached jpg a 3d file. I have a larger and more clear version that I already outlined but am tired of trying to figure this out right now... thanks.
by myshadowboxes
Fri May 20, 2011 2:28 pm
Forum: Aspire - Tips and Tricks
Topic: Trying to create a raised area of a pictue of a tree
Replies: 4
Views: 1943

Re: Trying to create a raised area of a pictue of a tree

Thanks Don.... I do most of what you said... But Most is not enough. Let me hit it again this morning. Michael, I knew about the setting by holding the Control key, but never thought it would help in this case. But then again, I guess it could.

Thanks, back to the drawing board
by myshadowboxes
Fri May 20, 2011 3:50 am
Forum: Aspire - Tips and Tricks
Topic: Trying to create a raised area of a pictue of a tree
Replies: 4
Views: 1943

Trying to create a raised area of a pictue of a tree

Ok, this is what I have a large oak tree and noting else. What I would like to do is create something under it to raise the middle like a bubble, just to give it some height. Not trying to do anything fancy. Here is what I am running into. When I bring the picture in, it is also bringing the area ar...
by myshadowboxes
Tue May 17, 2011 5:03 pm
Forum: Aspire - Tips and Tricks
Topic: Help with 2 rail sweep
Replies: 2
Views: 1180

Re: Help with 2 rail sweep

Hi Anthony, By the look of your first picture you have drawn your cross section skewed (the bottom of the left side is not level with the bottom of the right side). When Aspire sweepes this, it will attach the bottom of the left side of the cross section vector to the outside rail and the bottom of...
by myshadowboxes
Tue May 17, 2011 4:09 pm
Forum: Aspire - Tips and Tricks
Topic: Help with 2 rail sweep
Replies: 2
Views: 1180

Help with 2 rail sweep

This two rail sweep is going to be the death of me... Ok, this is what I have. The first picture shows the area with the two rail sweep. In the middle is going to be a hole. In the second picture it shows the two rail, but I would like the center when filled to be even with the lower part of the swe...
by myshadowboxes
Sun May 15, 2011 11:32 pm
Forum: Aspire - General
Topic: Looking for a side view of a motorcycle tire
Replies: 9
Views: 1756

Re: Looking for a side view of a motorcycle tire

Ok, well here is the final version... The white is to show the customer that I would do the black : ) half of the black is gloss and the other is flat. In the middle is where the local sign shop will place a logo. And of course it is a motocross tire. Thanks for all the help and support from everyon...
by myshadowboxes
Sun May 15, 2011 5:02 pm
Forum: Aspire - General
Topic: Looking for a side view of a motorcycle tire
Replies: 9
Views: 1756

Re: Looking for a side view of a motorcycle tire

That is too funny... before I read this, that is exactly what I did. I made two of the underlying shapes. It looks a little better now so I will go and run it on the machine. I tried to upload the file and then saw that it was 15 meg zipped. Not going to happen. I still can not figure out how to mak...
by myshadowboxes
Sun May 15, 2011 2:37 pm
Forum: Aspire - General
Topic: Looking for a side view of a motorcycle tire
Replies: 9
Views: 1756

Re: Looking for a side view of a motorcycle tire

That is exactly how I did it... here is my shape that is under the bitmap component. What I want to do is raise the arch where the outside two arrows are. I also want to raise the height of the middle to make it where it is 1/2 on the material. It looks as though I am only using 1/4 of the material ...