Search found 1048 matches
- Thu Jan 21, 2021 7:29 pm
- Forum: VCarve - General
- Topic: Newbie Questions
- Replies: 4
- Views: 89
Re: Newbie Questions
Yup! The Bit Diameter could be a possible problem on the outer perimeter if clamps are used for hold down of spoilboard! Might be better to create an new program within V-Carve that way you will know and understand all that is performed. A big plus to that is you get to use V-carve and familiarize y...
- Thu Jan 21, 2021 7:23 pm
- Forum: VCarve - General
- Topic: Depth of cut for Fluting toolpath
- Replies: 8
- Views: 193
Re: Depth of cut for Fluting toolpath
+1 Agreed
Vectric Support is the answer for that!
Sharkcutup
Vectric Support is the answer for that!
Sharkcutup
- Thu Jan 21, 2021 5:23 pm
- Forum: VCarve - General
- Topic: Newbie Questions
- Replies: 4
- Views: 89
Re: Newbie Questions
Welcome! The thing I noticed is that that particular model machine comes with two different size collets 1/4" and the 1/2". If you use the 45526 Router bit you will need to change the collet on the spindle to 1/4" collet because the bit has a 1/4" shank. Other than that some adjustments may be warra...
- Mon Jan 18, 2021 10:20 pm
- Forum: VCarve - General
- Topic: Hail The Tailmaker
- Replies: 7
- Views: 266
Re: Hail The Tailmaker
I had Grandparents who had lived in Windsor that is why I asked?
You be a long way from me for I am in the Deep South of the USA
Sharkcutup
You be a long way from me for I am in the Deep South of the USA
Sharkcutup
- Mon Jan 18, 2021 10:05 pm
- Forum: VCarve - General
- Topic: Hail The Tailmaker
- Replies: 7
- Views: 266
Re: Hail The Tailmaker
Horton Township Ontario Canada
Is that anywhere near Windsor, Ontario???
Sharkcutup
Is that anywhere near Windsor, Ontario???
Sharkcutup
- Mon Jan 18, 2021 7:58 pm
- Forum: VCarve - Gallery
- Topic: 3D without a Model
- Replies: 10
- Views: 441
Re: 3D without a Model
Nearly have this project ready to carve! Just a few more tweaks!
BTW - Easy fix on the mis-spelled Bethlehem!
Sharkcutup
BTW - Easy fix on the mis-spelled Bethlehem!
Sharkcutup
- Mon Jan 18, 2021 7:52 pm
- Forum: VCarve - Gallery
- Topic: Playing card Box
- Replies: 4
- Views: 169
Re: Playing card Box
Now that is a trick I would like to see!!and the cards are v-carved.

Awesome Project!!!
Sharkcutup
- Mon Jan 18, 2021 7:48 pm
- Forum: VCarve - General
- Topic: Hail The Tailmaker
- Replies: 7
- Views: 266
Hail The Tailmaker
Hail the Tailmaker!!! I have been looking for a joint to use for the Cat Exercise Wheel Frame so that the wheel itself can be assembled/disassembled at will anytime. I have created a joint using Tailmaker's PuzzleMyJoint Software! After Carving and a little sanding the joint went right together with...
- Mon Jan 18, 2021 2:42 am
- Forum: VCarve - General
- Topic: Last Pass and Preview
- Replies: 11
- Views: 366
Re: Last Pass and Preview
Thank you adze_cnc for the awesome explanation! And yup I didn't thoroughly understand the last pass function as Vectric has programmed/intended. And Gentlemen your responses have contributed also in getting an understanding of how and why the Last Pass Function may or may not be necessary. Great Fo...
- Sun Jan 17, 2021 9:27 pm
- Forum: VCarve - General
- Topic: Last Pass and Preview
- Replies: 11
- Views: 366
Re: Last Pass and Preview
Well my understanding was a bit off but ----
Adrian.
Ok what would you have if you use an offset of .003 and a last pass allowance of .003"?
Just want to better understand what is happening/occurring.
Sharkcutup
Adrian.
Ok what would you have if you use an offset of .003 and a last pass allowance of .003"?
Just want to better understand what is happening/occurring.
Sharkcutup
- Sun Jan 17, 2021 6:53 pm
- Forum: VCarve - General
- Topic: Last Pass and Preview
- Replies: 11
- Views: 366
Re: Last Pass and Preview
But it differs as it's lass pass is a whole new pass at full depth. Unlike VCarve's that makes the last cut through the material as the last pass. In my case, cutting the last 1/4" of the 1/2" material as the last pass and on the line vs offset by 0.003". V-Carve makes the last pass not only cuttin...
- Sun Jan 17, 2021 4:38 am
- Forum: VCarve - General
- Topic: Shifting mid cut
- Replies: 15
- Views: 449
Re: Shifting mid cut
Happy to hear you have gotten the problem resolved.
Sharkcutup

Sharkcutup
- Sat Jan 16, 2021 7:35 pm
- Forum: VCarve - General
- Topic: Help with spoon design
- Replies: 4
- Views: 184
Re: Help with spoon design
Here is your File with the moulding toolpaths added for the handle. https://www.dropbox.com/s/ovd3rpuq759xp56/Spoon.crv?dl=0 Spoon.png I Changed/added a few things and you can manipulate the moulding toolpath according to your liking. Be sure to adjust/edit the tools Feed/Speed settings used for you...
- Sat Jan 16, 2021 4:10 pm
- Forum: VCarve - General
- Topic: Last Pass and Preview
- Replies: 11
- Views: 366
Re: Last Pass and Preview
Put an allowance of .003 in the Allowance(A) box and it will work as you want it to. Below Taken from User Guide Do Separate Last Pass A separate allowance can be specified for the last pass. If this allowance is given then all but the last pass will be undercut by the specified allowance with the f...
- Fri Jan 15, 2021 6:51 pm
- Forum: VCarve - General
- Topic: Eliminate thumb drive?
- Replies: 10
- Views: 514
Re: Eliminate thumb drive?
In addition to having computers networked I regularly backup all my V-Carve files including Post Processors, Tool Database, Material textures, and any clipart I may have added to the clipart files.
Sharkcutup
Sharkcutup