Search found 27 matches

by good1
Thu Nov 26, 2020 8:06 pm
Forum: VCarve - General
Topic: V10.5
Replies: 12
Views: 2780

Re: V10.5

I want to thank every one who tried to help. I got it to start working again, I uninstalled CNC shark CP2.1 and then reinstalled CNC shark CP 2.1 and now it works just fine so far.....Thanks again
by good1
Wed Nov 25, 2020 3:22 pm
Forum: VCarve - General
Topic: V10.5
Replies: 12
Views: 2780

Re: V10.5

I asked nextwave about that and was told it can happen.
by good1
Wed Nov 25, 2020 1:33 am
Forum: VCarve - General
Topic: V10.5
Replies: 12
Views: 2780

Re: V10.5

I just uninstalled v10.5... Then I calculated useing v10.022 post processor CNCshark-USBinch . (nextwave processor starts in v10.5 I guess) a test box 4"x8" .75" thick.. Loaded it into the controlor, pushed the RUN button ,and the same thing happend,,, nothing. I have been using the black diamond si...
by good1
Tue Nov 24, 2020 4:54 pm
Forum: VCarve - General
Topic: V10.5
Replies: 12
Views: 2780

Re: V10.5

As far as I can tell I have used the same post processer since I installed v9.
by good1
Tue Nov 24, 2020 3:51 pm
Forum: VCarve - General
Topic: V10.5
Replies: 12
Views: 2780

Re: V10.5

I used the CNCshark-USB-(inch)(*tap). Is there another one???
by good1
Mon Nov 23, 2020 11:29 pm
Forum: VCarve - General
Topic: V10.5
Replies: 12
Views: 2780

Re: V10.5

can I uninstalling v10.5 and just use v10. I think that when I installed v10.5 it did something to the controlor , because when I used v10 It cut just fine....
by good1
Mon Nov 23, 2020 10:30 pm
Forum: VCarve - General
Topic: V10.5
Replies: 12
Views: 2780

V10.5

When I installed v10.5 on my cpu and opened up a file and down loaded the gcode there were green and black dots where the vectors were and the vectors would not cut. what did I do wrong?????
by good1
Sun Jun 28, 2020 10:25 pm
Forum: VCarve - General
Topic: design and make models
Replies: 1
Views: 815

design and make models

I have the western scenes and wilderness scenes on another cpu how can I install them on my new cpu????
by good1
Wed Aug 02, 2017 8:43 pm
Forum: Cut3D - General
Topic: setting of Z after rough cut 3D
Replies: 1
Views: 3049

setting of Z after rough cut 3D

How do I zero out the Z after rough cutting? Can the Z axes be zeroed out on the edge of the material then hit move to x0 y0 to the center datum point.? The datum position is set for center of the material. I know I can use the lower left edge. I noticed that Jeff Searles leaves his datum in the cen...
by good1
Wed Aug 02, 2017 6:00 pm
Forum: Cut3D - General
Topic: 3D preview
Replies: 11
Views: 7794

Re: 3D preview

I did the same toolpaths on two other computers one is running win 7 and is 10 years old. The other one is running win 10 and is three years old, the preview came out great on both computers. The computer that has a bad preview is running win 10 and is only two years old. What is going on??? Thanks ...
by good1
Tue Aug 01, 2017 12:19 am
Forum: Cut3D - General
Topic: 3D preview
Replies: 11
Views: 7794

Re: 3D preview

That is what I thought . I used a .25 end mill with a 40% stepover and a ballnose .125 with a 7% stepover, raster 0.0
by good1
Tue Aug 01, 2017 12:12 am
Forum: Cut3D - General
Topic: 3D preview
Replies: 11
Views: 7794

Re: 3D preview

The gorilla model came with vcarve 8.5
by good1
Mon Jul 31, 2017 8:10 pm
Forum: Cut3D - General
Topic: 3D preview
Replies: 11
Views: 7794

Re: 3D preview

I would need some info on how to send toolpath and other info . I am not too computer savy. thanks
by good1
Mon Jul 31, 2017 7:28 pm
Forum: Cut3D - General
Topic: 3D preview
Replies: 11
Views: 7794

3D preview

I am useing a 3D gorilla clipart from vectric for a 6x7 box top. After previewing cutting the rough cut with a .25 end mill. I set my finish cut at .04 below the survace for the finish cut. When I preview the finish toolpath it is not smoth like the model. Will it cut like the preview or will it car...
by good1
Tue Jul 04, 2017 12:19 am
Forum: VCarve - General
Topic: inlays
Replies: 4
Views: 2595

Re: inlays

Thanks for the reply.. That is my problem I do not know how to isolate a section or part from each other. any help would be great. thanks, gene