Search found 9 matches
- Tue Jan 02, 2018 11:41 pm
- Forum: Gadgets - User Submissions
- Topic: Chamfer Radius Gadget - New Gadget
- Replies: 39
- Views: 53921
Re: Chamfer Radius Gadget - New Gadget
Here is the Vcarve pro message I get when I try to apply the Chamfer Radius gadget. The gadget starts fine and lets me pick the option I want, hit OK and this is what shows up
- Tue Jan 02, 2018 4:11 pm
- Forum: Gadgets - User Submissions
- Topic: Chamfer Radius Gadget - New Gadget
- Replies: 39
- Views: 53921
Re: Chamfer Radius Gadget - New Gadget
I did some asking about an issue with Vectrics Chamfer gadget, and they did a new upload on their gadget collection to fix the issue. I also asked about the Chamfer Radius gadget that I got off this forum last year.. here is that exchange ----------------------- Mark Moran (Vectric Ltd.) Jan 2, 14:4...
- Mon Jan 01, 2018 7:12 pm
- Forum: Gadgets - General
- Topic: gadget not working
- Replies: 11
- Views: 14048
Re: gadget not working
Found this solution in another post by Adrian, applied the edit he suggested and chamfer gadget now works fine, THANKS to Adrian... Re: chamfer gadget 1.3 doesn't work in v. 9.012 Unread postby Adrian » Tue Dec 05, 2017 4:48 pm The installation path is correct as far as I know. It's only gadgets tha...
- Mon Jan 01, 2018 6:42 pm
- Forum: Gadgets - General
- Topic: gadget not working
- Replies: 11
- Views: 14048
gadget not working
V carve Pro 9.012, updated and current… installed the chamfer gadget from the Vectric gadget site.... I select a vector I want to run it on, and this is the message I receive.. "attempt to call a nil value" ....tried restarting, re install numerous times ..keep getting same result Using Chrome Any h...
- Mon Jul 11, 2016 1:49 pm
- Forum: VCarve - General
- Topic: Vbit issue I can't figure out
- Replies: 7
- Views: 3292
Re: Vbit issue I can't figure out
The issue shows up in the preview pane. My guess is the problem is your bit selection. The v-bit you're trying to use for your final pass is a 30 degree, 1/4" wide bit. The spaces that are giving the problems look about 1/4" wide or less. Maybe the computer can't figure out if you want it to just c...
- Mon Jul 11, 2016 1:40 pm
- Forum: VCarve - General
- Topic: Vbit issue I can't figure out
- Replies: 7
- Views: 3292
Re: Vbit issue I can't figure out
"There is something not right about the corners where the v bit has been in the photo. They are far too rounded." I went over a couple spots with a dremel tool to see if I could improve on the situation, I think that is what you are seeing.... The more I look at this it seems that my issue has more ...
- Sun Jul 10, 2016 4:06 pm
- Forum: VCarve - General
- Topic: Vbit issue I can't figure out
- Replies: 7
- Views: 3292
Re: Vbit issue I can't figure out
Probotix Meteor machine ... It has an auto tool sensor that checks tool after each change, I zero all axis' at the start of the file. It cuts at the proper "Z" level while doing the first part of the tool cut, it when it cleans out the corners that the "Z" level appears to change... ...crv file is t...
- Sun Jul 10, 2016 1:30 pm
- Forum: VCarve - General
- Topic: Vbit issue I can't figure out
- Replies: 7
- Views: 3292
Vbit issue I can't figure out
I have a pocket cut that uses a 30 deg V and a 1/4" end mill. Pocket is set between the letters and the border ... The end mill does it's work, the 30 deg Vbit does it's cut around the letters and then goes after the corners and small pockets. When this starts, it appears the bit drops down to anoth...
- Fri Mar 18, 2016 4:12 pm
- Forum: VCarve - General
- Topic: Copy Registered copy of VcarvePro to laptop
- Replies: 5
- Views: 3021
Re: Copy Registered copy of VcarvePro to laptop
If the 3 copies are in use, computer in shop, one at home, laptop ...and one of those computers is replaced, can I transfer from the replaced unit to a new one?