Search found 36 matches

by hmatyas
Sun Mar 28, 2021 7:30 pm
Forum: Laser Module - General
Topic: Laser Module Performance
Replies: 15
Views: 3540

Re: Laser Module Performance

Thank you for both replies, I guess I will just sit back and wait. At least I did not buy a controller thinking that it would solve the problem.
by hmatyas
Sun Mar 28, 2021 2:26 am
Forum: Laser Module - General
Topic: Laser Module Performance
Replies: 15
Views: 3540

Re: Laser Module Performance

Hi Has the problem with the Shark HD4 and HD5 been resolved? I purchased the laser module and I have a Shark HD3. I know that it does not work with the HD3 but was looking into acquiring a HD5 controller. However, it looks like this would not be wise because it appears that the HD5 controller does n...
by hmatyas
Sat Mar 27, 2021 1:58 am
Forum: VCarve - General
Topic: I can't find 3D clipart
Replies: 2
Views: 758

Re: I can't find 3D clipart

Adrian

Thank you, I'll go look for them.

Harvey
by hmatyas
Thu Mar 25, 2021 10:40 pm
Forum: Design & Make Clipart- General
Topic: Free #d Clipart EOT Celebration
Replies: 2
Views: 1269

Re: Free #d Clipart EOT Celebration 3D clip art

The subject should be Free 3D clipart EOT Celebration.
by hmatyas
Thu Mar 25, 2021 10:39 pm
Forum: Design & Make Clipart- General
Topic: Free #d Clipart EOT Celebration
Replies: 2
Views: 1269

Free #d Clipart EOT Celebration

I don't know if this is the correct area to post this question. I downloaded the Free 3D Clipart EOT - Celebration several different times. It is properly download and I installed it. I just can't find it when I am in Vcarve Pro. I have installed other files and have not had any problems finding the...
by hmatyas
Wed Feb 10, 2021 9:43 pm
Forum: Aspire - General
Topic: Angle profile slide not working
Replies: 2
Views: 372

Re: Angle profile slide not working

Thank you. I was confused why only those two didn't work. But when I clicked off of them it did.
by hmatyas
Wed Feb 10, 2021 8:26 pm
Forum: Aspire - General
Topic: Angle profile slide not working
Replies: 2
Views: 372

Angle profile slide not working

Hi I am trying the Aspire trial 10.5 and I drew a circle. Going to the create a shape from profile. The dome profile works fine, however, when I click on the concave or the flat profile, the angle slider and the box to enter angle gets grayed out. The angle and smooth profile also works. Is this the...
by hmatyas
Mon Feb 08, 2021 6:16 pm
Forum: VCarve - General
Topic: Smart snap to intersection of 2 overlapping circles
Replies: 5
Views: 339

Re: Smart snap to intersection of 2 overlapping circles

I think that works! The first time I tried it it didn't now it does. I first copied 4 circles that made the pie piece to the Try layer. Then I used the vector trim to get a rectangle. Then using smart snapping, I drew a line to cut the rectangle in half. Then I used the vector trim to get a pie shap...
by hmatyas
Mon Feb 08, 2021 5:49 pm
Forum: VCarve - General
Topic: Smart snap to intersection of 2 overlapping circles
Replies: 5
Views: 339

Re: Smart snap to intersection of 2 overlapping circles

If I'm following you correctly, that does not work (at least for me). What happens when I move the guides to the spot, you can't (at least I can't) position it exactly on the intersection. By this I mean after I click the guide where I believe the intersection of the two curves are and the guide lin...
by hmatyas
Sun Feb 07, 2021 7:34 pm
Forum: VCarve - General
Topic: Smart snap to intersection of 2 overlapping circles
Replies: 5
Views: 339

Smart snap to intersection of 2 overlapping circles

I have a 11.5 inch circle at 0,0 and a 5.75 inch circle at 0,2.875 (circle touches circumference and 0.0) Then I do a circle array at 0,0 and create 36 circles of the smaller one. (all touch circumference and 0,0) I would like to draw circles of different diameters from 0,0 that touches intersection...
by hmatyas
Sun Dec 13, 2020 4:38 am
Forum: VCarve - Gallery
Topic: Cut this snowman on my 4th axis
Replies: 4
Views: 817

Re: Cut this snowman on my 4th axis

Hi

Thank you for your interest. This was my first video so it's not that good.



But the link above should take you there.

Thank you.

Harvey
by hmatyas
Sun Dec 13, 2020 4:34 am
Forum: VCarve - Gallery
Topic: Candy Cane Ornaments done on my 4th axis
Replies: 3
Views: 544

Re: Candy Cane Ornaments done on my 4th axis

I used a ribbon tried with a square knot. There is a youtube video on Candy Cane Ornaments from As Wood Turns where he describes everything in great detail. I used that idea to make mine on the 4th axis. The big difference was drill the hole for the candy cane. He just had a drill bit and moved it i...
by hmatyas
Sat Dec 12, 2020 5:48 pm
Forum: VCarve - Gallery
Topic: Candy Cane Ornaments done on my 4th axis
Replies: 3
Views: 544

Candy Cane Ornaments done on my 4th axis

I just finished these 4 candy cane ornaments for my grandkids.
I basically did everything except for cutting the wood to size, drilling the hole for the string
and sanding, on my CNC machine and my 4th axis.
by hmatyas
Tue Dec 08, 2020 6:23 pm
Forum: Gadgets - General
Topic: Sometime file opens as Vcarve 10.0 not 10.5
Replies: 3
Views: 1365

Re: Sometime file opens as Vcarve 10.0 not 10.5

Thank you Adrian, I did not know that this procedure actually existed.
by hmatyas
Mon Dec 07, 2020 11:24 pm
Forum: Gadgets - General
Topic: Sometime file opens as Vcarve 10.0 not 10.5
Replies: 3
Views: 1365

Re: Sometime file opens as Vcarve 10.0 not 10.5

I paid a little more attention when I tried to install another gadget. When I open the gadget after I download it, it installs on version 10.0.
How do I make it install on version 10.5?

Thank you.