Search found 63 matches
- Wed May 10, 2023 1:43 am
- Forum: Aspire - General
- Topic: Project of the Month
- Replies: 2
- Views: 718
Project of the Month
Just wondering if Michael is OK, haven't seen any new projects lately. Hope all is well.
- Wed Jan 13, 2021 2:46 am
- Forum: Aspire - General
- Topic: Best way do design spoil board grid
- Replies: 9
- Views: 3090
Re: Best way do design spoil board grid
Great info folks, sorry but busy in the garage and was able to use the draw line tool and snap a line every 1 inch in both directions to get the grid I needed. Very tedious to say the least but was effective. Used Amana 45 deg Vbit with .03 DOC to get what I was looking for. highpockets thanks for t...
- Tue Jan 12, 2021 3:27 pm
- Forum: Aspire - General
- Topic: Best way do design spoil board grid
- Replies: 9
- Views: 3090
Re: Best way do design spoil board grid
I'm looking for best design practices in Aspire.
Thanks
Thanks
- Tue Jan 12, 2021 1:46 pm
- Forum: Aspire - General
- Topic: Best way do design spoil board grid
- Replies: 9
- Views: 3090
Best way do design spoil board grid
I'm going to skim my spoil board and was wondering the best way to design a V grove grid that is efficient to tool.
Thinking of a 30deg bit with very little DOC.
I know about the Array Copy feature but if I use that and combine the lines will that toolpath be efficient?
Thanks
Thinking of a 30deg bit with very little DOC.
I know about the Array Copy feature but if I use that and combine the lines will that toolpath be efficient?
Thanks
- Sat Jul 11, 2020 4:00 pm
- Forum: Laser Module - General
- Topic: Laser Module Toolpaths tab.
- Replies: 15
- Views: 5392
Re: Laser Module Toolpaths tab.
Adrian, once again thanks, just added my own tool and all is fine.
Looking forward to trying this Laser Option out.
Off to the shop
Looking forward to trying this Laser Option out.
Off to the shop
- Sat Jul 11, 2020 2:50 pm
- Forum: Laser Module - General
- Topic: Laser Module Toolpaths tab.
- Replies: 15
- Views: 5392
Re: Laser Module Toolpaths tab.
OK, got my PP's to show up by copying the new X carve processors to MY_PP folder. Now when I try to select a tool from the Laser tool-path I get the attached picture with the Toolstoday Master showing. The other picture is my actual Tool Database for everything else.
Any ideas on this?
Any ideas on this?
- Fri Jul 10, 2020 9:49 pm
- Forum: Laser Module - General
- Topic: Laser Module Toolpaths tab.
- Replies: 15
- Views: 5392
Re: Laser Module Toolpaths tab.
Adrian, thanks for your help. Much appreciated.
- Fri Jul 10, 2020 9:18 pm
- Forum: Laser Module - General
- Topic: Laser Module Toolpaths tab.
- Replies: 15
- Views: 5392
Re: Laser Module Toolpaths tab.
wb9tpg, I think there is an issue but just hoping because it's a new feature.
- Fri Jul 10, 2020 8:16 pm
- Forum: Laser Module - General
- Topic: Laser Module Toolpaths tab.
- Replies: 15
- Views: 5392
Re: Laser Module Toolpaths tab.
I went to Jtech site https://jtechphotonics.com/?p=3851 and copied the GRBL inch version and put it in My_PostP folder and it still didn't show up.
Thanks for your help but no worries, I have too much else to learn to worry about this now.
thanks
Thanks for your help but no worries, I have too much else to learn to worry about this now.
thanks
- Fri Jul 10, 2020 5:19 pm
- Forum: Laser Module - General
- Topic: Laser Module Toolpaths tab.
- Replies: 15
- Views: 5392
Re: Laser Module Toolpaths tab.
Thanks Adrian, where in the Application Data Folder are the Laser Module PP's located? Iv'e migrated everything from version 10 and my shop computer shows nothing but a Laptop shows a hand full of PP's in the laser toolpaths. Interesting indeed.
- Fri Jul 10, 2020 3:59 pm
- Forum: Laser Module - General
- Topic: Laser Module Toolpaths tab.
- Replies: 15
- Views: 5392
Laser Module Toolpaths tab.
Aspire 10.5 On both the Laser toolpaths tabs the Post Processor when clicked show nothing. How do I get my PP to show up under this drop down?
- Tue Jul 07, 2020 9:48 pm
- Forum: Aspire - General
- Topic: Laser Module
- Replies: 4
- Views: 1547
Re: Laser Module
Thanks that worked, now I just need to figure how to add my J-Tech Laser to the database.
- Tue Jul 07, 2020 9:39 pm
- Forum: Aspire - General
- Topic: Laser Module
- Replies: 4
- Views: 1547
Re: Laser Module
AdamJ, thanks was able to purchase and see the info on my Vectric account but where is the download button to add to Aspire. I clicked on the product installers and re-downloaded and ran the setup but no laser tools are installed.
Just wondering
Just wondering
- Tue Jul 07, 2020 8:27 pm
- Forum: Aspire - General
- Topic: Laser Module
- Replies: 4
- Views: 1547
Laser Module
I just upgraded to my free 10.5 Aspire and I was wondering where to find the new Laser Module and where to purchase the same. Must be in front of my nose because I don't see it.
Thanks
Thanks
- Thu Jul 02, 2020 10:32 pm
- Forum: Aspire - General
- Topic: Adding Clip Art to a Dish
- Replies: 3
- Views: 1334
Re: Adding Clip Art to a Dish
My post states that they are all Merged.